Neil A. Kruiswyk wrote:
Gentlemen,
Keep in mind that an exit flap is mandatory for all of this to work. If
you need more cooling, open the flap. Idealy, we want to keep the engine
temp at the point where the engine thermostat is just at it's wide open
point. Higher and we start to over heat. Lower and we have excessive
cooling ergo, excessive drag. Simply put (for those of brain power equal to
my own) we're using the cowl flap as a thermostat.
It looked odd to me too at first but here's what one expert in the field
had to say....
Neil
On the issue of inlet and exit areas, most commonly people make inlets too
small and outlets too large. This is the usual condition on experimentals,
and Lance did it on his aircraft. One needs to slow the flow and recover
the
velocity pressure before passing through the core or over the air cooled
engine. There are two ways to do it - Slow the flow in front of the inlet
(by
pushing a blunt object through the air like the front of an airplane) or
slow
the flow after it comes into the inlet. In the latter case, you have all
kinds of skin friction, boundary layer and flow separation effects to fight
off (flow does not like to go uphill against increasing pressure). Slowing
the flow outside of (in front of) the inlet is more efficient, but in
extreme
cases will lead to flow separation as the flow spills over the edge of the
inlet.
Jet aircraft count on slowing the flow in front of the nacelle to recover as
much pressure as possible before inducting flow into the engine. The stream
tube area (area of the tube of flow in front of the engine that contains the
air that will flow into the inlet) is much smaller than the engine inlet
area
when cruising at high altitude and high speed. The flow diverges strongly
and
much spills over the outside of the inlet. But the pressure at the inlet of
the nacelle is higher than ambient because of the flow curvature.
The NASA work with an Aztec in the early 80's showed that the best inlet had
an area 3.3 times larger than the stream tube that fed it. This proves to
be
too large for most installations (not enough room) and the later work by
Lopresti and others showed that you can do nearly as well with inlet ratios
of
2 to 2.5. My numbers assume an inlet ratio of 2.5 (that is the inlet area
in
the cowl is 2.5 time larger than the stream tube areas that feeds it). This
converts most of the kinetic energy in the free stream into pressure before
it
goes into the cowl where the rest of the conversion takes place.
At the outlet, the idea is to recover the momentum lost when slowing the
flow
by reaccelerating it and pointing it aft like a fire nozzle. The limitation
is how much pressure is left over to accelerate the flow through the nozzle
once it has passed thorough the core or over the engine. If you have lots
of
pressure left over (usually the case with radiators since they have lower
pressure drop than air cooled engines for the same flow) you can convert the
excess pressure left over into velocity by squirting it out the discharge.
Since the exiting flow is hotter, its density is lower, and theoretically
you
can accelerate the flow to an exit velocity higher than the inlet velocity
(this is how ram jets work) but it takes speed and low friction to make it
work.
In the case of air cooled engines, the pressure drop across the engine is
quite high, so there is not much pressure left over to accelerate the flow
aft. Consequently designers usually just dump the flow out into the free
stream and accept the drag penalty. But if you don't have to do it, why pay
the penalty? W.W.II aircraft designers recognized this with air cooled
engines and the ring cowl flaps used on radial engines. Early designs had
large outlet areas with cowl flaps open (for ground and climb operation) and
outlets smaller than inlets for high speed cruise (cowl flaps closed). The
late radial engine fighters, particularly the Sea Fury, carried this farther
with annular inlets, big spinners which helped compress the flow before it
entered the cowl, and outlets that were quite small since they were going
fast.
So, the current "wizdumb" is make the inlet larger, have good radiused lips
on the inlet so the excess flow can spill smoothly over the outside when in
high speed flight, have an outlet large enough to pass the required flow
under
worst conditions, use a cowl flap to adjust the area and create some suction
for the worst case conditions, and then close the outlet area down to the
minimum feasible to minimize drag. On my draggy C-182 (retractable), the
speed difference between cowl flaps open and closed is about 6-7 knots, more
at higher altitudes. On your plane with lower drag and higher speed, it
should be more.
Happy building.
Fred
This is neat. Sounds up to date. Where did you find this guy Neil?
Thank him for me. I would like to meet him sometime. Is he coming
to Oshkosh?
Take a lot of pictures while your building this so we can see
all the details.
Paul Lamar
The Aircraft Rotary Engine Newsletter. Powered by Linux.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org