TERF Email wrote:
Hi Paul
I have some experience with that computer. As I recall there are a
couple of "back door" ways of dealing with the problem. These are legit
design in repair methods.... Nothing hokey. There is a connector "easily
accessible" right under the steering wheel. It will probably have several
"stations" in it with only like 2 populated with a wire. If you short
between these things and immediately look at the "check engine light" it
will flash a "Morse code" type signal in about 1 second duration's. This is
called the "flash code". There are charts where you look up this code and
it tells you exactly what the problem is. (I.E. bad spark plug wires.)
These codes and more information can be found in manuals (like Chiltons
etc.) I think. Anyway they can be found. There is also about a $200 ish
hand held pendant computer that you can plug into the connector and get an
English printout of the problem. It is expensive and you have to have the
"game cartridge" for that type of vehicle. Different vehicle, different
game cartridge. My brother has one of these and it works nice but the flash
code method is way cheap and portable (usually a paper clip will do) ;-)
NOW to clear the check engine light code..... I am pretty sure that
they all work the same..... Disconnect the battery wait 30 seconds and
reconnect. This should do the trick.
I own GM vehicles of the vintage you have. I have worked with MANY Ford
vehicles slightly older. I am pretty sure these things will work for you.
Murrys sells spark plug wires, cap and rotor for that engine for about
$40, $18 & $ $8 respectively.
Welcome to shade tree mechanic in the high tech era.
Let me know if this works for ya.
Best Regards
Matthew Tait Of TERF Inc.
Mine is the first of the OBD II's. I don't think that works any more.
The D connector is standardised among brands but the serial protocol
is unique to Ford products. 10K baud... pulse width modulated.
Standard RS232 is NRTZ coded. Non Return To Zero as I recall.
My connector is below the glove compartment.
It is not an RS232 nor is the connector a D submin.
It is a node on a local area network within the car.
Shorting any of the wires could cause problems.
I have a complete set of the SAE papers on OBD II plus a lot of
Ford information on the subject. I studied it for six months.
I am looking for somebody with software that runs on a notebook
computer that will read out diagnostic codes. So far no luck.
I have tons of material on this subject if you are interested.
It would be a good business to get into as the crap will hit the
fan soon as a lot of these cars get older and need repair.
PL
[EPA]United States Environmental Protection Agency
Office of Air and Radiation
Office of Mobile Sources
EPA 420-F-97-003
May 1997
Frequently Asked Questions About On-Board Diagnostics
The Environmental Protection Agency has regulations in place
establishing
requirements for on-board diagnostic (OBD) systems on light-duty
vehicles
and light-duty trucks beginning with the 1994 model year. The purpose of
the OBD system is to assure proper emission control system operation for
the vehicle's lifetime by monitoring emission-related components and
systems for deterioration and malfunction.
What is OBD And How Does It Work?
By the early 1980's, numerous vehicles were using electronics and
on-board
computers to control many of the engine's control systems, such as fuel
and
ignition. Vehicle manufacturers had to develop ways to diagnose problems
generated by the new electronic hardware found under the hood. Thus, the
first OBD systems were developed by auto manufacturers in the early
1980's
as electronic systems replaced mechanical systems.
The engines in today's vehicles are largely electronically controlled.
Sensors and actuators sense the operation of specific components (e.g.,
the
oxygen sensor) and actuate others (e.g., the fuel injectors) to maintain
optimal engine control. An on-board computer, known sometimes as a
"powertrain control module" or an "engine control unit," controls all of
these systems. With proper software, the on-board computer is capable of
monitoring all of the sensors and actuators to determine whether they
are
working as intended. It can detect a malfunction or deterioration of the
various sensors and actuators, usually well before the driver becomes
aware
of the problem through a loss in vehicle performance or driveability.
The
sensors and actuators, along with the diagnostic software in the
on-board
computer, make up what is called "the OBD system."
What Is The Connection Between OBD And Vehicle Emissions?
There are circumstances under which the vehicle computer will detect a
system problem before the driver notices a driveability problem.
Furthermore, OBD can detect problems that may not be noticeable upon
visual
inspection because many component failures that impact emissions can be
electrical or even chemical in nature. By detecting these
emission-related
failures and alerting the driver to the need for potential repair, EPA
hopes that vehicles will be properly repaired before emissions become a
problem.
How Does OBD Inform Drivers Of Problems?
When the OBD system determines that a problem exists, a corresponding
"Diagnostic Trouble Code" is stored in the computer's memory. The
computer
also illuminates a dashboard light indicating "Service Engine Soon" or
"Check Engine" or displays an engine symbol. This light, usually yellow
in
color, serves to inform the driver that a problem has been detected and
vehicle service is needed. When the car is delivered to the repair shop,
a
service technician can quickly retrieve the stored diagnostic trouble
codes
from the computer memory of the vehicle using newly developed diagnostic
tools. Since the diagnostic trouble codes will specifically identify the
problem, the service technician can more quickly and accurately make the
proper repair.
It is important to note that an illuminated dashboard light, as
described
here, is intended to inform the driver of the need for service, NOT of
the
need to stop the vehicle. However, service should be sought as soon as
possible. Drivers also may wish to consult a repair shop or their
vehicle
owner's manual for further guidance.
Why Does The Dashboard Light Blink Or Flash?
Under certain conditions, the dashboard light will blink or flash. This
indicates a rather severe level of engine misfire. When this occurs, the
driver should reduce speed and seek service as soon as possible. Severe
engine misfire over only a short period of time can seriously damage
emission control system components, especially the catalytic converter,
which is typically the most expensive to replace. Drivers should also
consult their vehicle owner's manual for manufacturer specific
information.
How Can The Dashboard Light Be Turned Off?
After fixing the problem, the service technician will the turn off the
dashboard light. There are also situations under which the vehicle's OBD
system can turn off the dashboard light automatically if the conditions
that caused a problem are no longer present. If the OBD system evaluates
a
component or system three consecutive times and no longer detects the
initial problem, the dashboard light will turn off automatically. As a
result, drivers may see the dashboard light turn on and then turn off.
For
example, if the gas cap is not properly tightened after refueling, the
OBD
system can detect the vapor leak that exists from the cap not being
completely tightened. If the gas cap is subsequently tightened, the
dashboard light should be extinguished within a few days. This is not an
indication of a faulty OBD system. In this example, the OBD system has
properly diagnosed the problem and accordingly alerted the driver by
illuminating of the dashboard light.
How Does OBD Help The Environment?
The intent of OBD systems is to assure proper emission system operation
of
each and every vehicle and light truck for its lifetime by monitoring
emission-related components and systems for malfunction and/or
deterioration. An important aspect of OBD is its ability to notify the
driver of a problem before the vehicle's emissions have increased
significantly. If the vehicle is taken to a repair shop in a timely
fashion, it can be properly repaired before any significant emission
increase occurs. OBD systems will also provide automobile manufacturers
with valuable feedback from their customers' vehicles that can be used
to
improve vehicle and emission control system designs.
How Does OBD Help Consumers?
OBD systems are designed to alert drivers when something in the emission
control system begins to deteriorate or fails. Early diagnosis followed
by
timely repair can often prevent more costly repairs on both emission
control systems and other vehicle systems that may affect vehicle
performance such as fuel economy. For example, a poorly performing spark
plug can cause the engine to misfire, a condition sometimes unnoticed by
the driver. This engine misfire can, in turn, quickly degrade the
performance of the catalytic converter. With OBD detection of the engine
misfire, the driver would be faced with a relatively inexpensive spark
plug
repair. However, without OBD detection, the driver could be faced with
an
expensive catalytic converter repair in addition to the spark plug
repair.
In addition, manufacturers have increased incentive to build a higher
quality vehicle with better performance, reduced emissions, and more
efficient powertrains to prevent problems that can lead to OBD
detection.
OBD systems will also provide far more information than ever before to
help
auto technicians diagnose and properly repair vehicles during their
first
visit to the repair shop, saving time and money for consumers.
Are OBD-Related Repairs Covered By Warranty?
Federal law requires that the emission control systems on 1995 and later
model year vehicles be warranted for 2 years or 24,000 miles. Many auto
makers provide extended warranty coverage beyond what is currently
required
by federal law. Federal law also requires that the on-board computer and
the catalytic converter on 1995 and later model year vehicles be
warranted
for 8 years or 80,000 miles.
Can Anyone Service An OBD-Related Problem?
Only qualified, trained technicians equipped with the newest diagnostic
and
repair equipment should conduct OBD related service. All dealerships and
independent repair shops should have qualified personnel for conducting
OBD
related repairs. Vehicle owners should ask their dealer and independent
repair shops if their technicians have received proper training and have
access to the necessary equipment to properly service OBD equipped
vehicles.
Will Aftermarket Parts Work With OBD?
Most aftermarket parts should work with OBD systems, but there is no
guarantee. It is the responsibility of aftermarket parts manufacturers
to
ensure that their parts work properly with the vehicle for which they
are
designed. This is even more true for OBD. The OBD regulations have
required
manufacturers to devise technologies and monitoring strategies that
didn't
previously exist. However, EPA is confident that aftermarket part
manufacturers who do a thorough job of replicating original equipment
manufacturer parts and those who carefully develop speciality parts will
be
able to produce parts that work with the OBD system.
---------------------------------------------------------------------------
For More Information:
For more information on federal on-board diagnostic regulations please
contact:
Holly Pugliese
U.S. EPA
Office of Mobile sources
2565 Plymouth Road
Ann Arbor, MI 48105
Phone:
313-668-4288
E-mail:
pugliese.holly@epamail.epa.gov
Or, visit the Office of Mobile Sources World Wide Web Home Page at:
http://www.epa.gov/OMSWWW/
and follow the path: "Automobiles" "I/M & OBD" "On-Board Diagnostics
Files."
[OMS Home] [EPA home] [Related links] [Air Quality] [ Search OMS web
site]
[Comments]
url: http://www.epa.gov/omswww/obd-faq.htm
Last update: 20 June 1997
The Aircraft Rotary Engine Newsletter. Powered by Linux.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org