Subject: GM-Drive-OBD2: 96 Chev/GMC Truck Suburban, Hesitation/Surge/MIL]
From: Paul
Date: 5/11/1999, 8:17 AM
To: zz

Brian D. Cain wrote:

I've got one thing to say about that:

"Hello, aftermarket, electronic fuel injection."


That entire text down there is yet one more reason why I DO NOT *ever*
take my car to a dealership.  *Ever*.



I wonder how much this person spent on all of that useless stuff?  It's
a 1996 car for God's sakes.  My 1988 doesn't have anywhere near those
problems.


B


Does not work in CA Brian. They will not let use replace
any OEM equipment with aftermarket equavalents. Especially
the whole fuel injection system. This will soon happen
in the rest of the states. We need to nip this in bud
politically and force the manufacturers to release far
more information on the software logic they use when building power
train managment computers.

Paul Lamar

----------
From:  Paul
Sent:  Tuesday, May 11, 1999 9:47 AM
To:  Allen Lyons CARB
Subject:  GM-Drive-OBD2: 96 Chev/GMC Truck Suburban, Hesitation/Surge/MIL

How many of these do I need to send to you Allen
before the EPA/CARB gets the point :-)

Paul Lamar


iATN Help:      send blank email to: help@i-atn.com
Upgrade:        http://members.iatn.net/enhanced.html
Archives:       http://members.iatn.net/sponsorsindex.html
Post Message:   http://members.iatn.net/email/
_______________________________________________________

1996 Chev/GMC Truck Suburban 5.7 L

Trans:         Automatic
Mileage:       82,676 miles
VIN:           3GKFK1GR4TG503227
Fuel:          Vortec SEFI
Emissions:     OBD-II Compliant

Symptoms:      Hesitation, Surge, Misfire, MIL Lamp on
Occurs:        Hot, Cruise

____________________________________________________________

Hello fellow Techs, Vehicle came to another Tech in shop on
3 March 99 with SES light and running rough. Tech scanned
codes, found all below codes and replaced EGR valve.
Cleared codes, test drove and claimed it ran O.K. Customer
drove to Wisconson on April 12 99 and visited a shop there
with a complaint of SES light , dying at stops and no
power. They put in plugs, cap, rotor, fuel filter and PCV
valve. Cleared P0300 code and said it ran fine. Came back
to the original Tech at our shop on 1 May with SES light on
and surge miss chuggle. He pulled plenum and quit. I came
in , found static fuel pressure dropping. Pinch off supply
line, static holds. Replace fuel pump and strainer. static
fuel pressure holds well. Injector balance is dead even at
9 psi. Spray on all injectors looks good when pulsed with
Tech 2 and inj. setup.. Test drive to find that it shakes,
shudders severly when at steady throttle above 45 mph.
While this is happening the misfire monitor shows hundreds
of misfires on all 8 cyl. Step on the brake - no change.
Accelerate - it goes away, in fact it runs excellent at
WOT. Decelerate and it eventually quits. I also noticed
that it will misfire during the split second lag between
upshifts and ever so slightly but barely noticeable below
45 mph. I have tried top engine cleaner, plug wires, Crank
sensor. All Data stream values look good. Fuel trim long
and short stay 124-128 while this is happening and fuel
pressure remains constant. It only sets off the misfire
monitor and flashes the SES light(it misses that bad). What
am I not seeing here? I have spent hours on the phone with
GM Tech to no avail. All the help is greatly appreciated.
Lance Wheeler ( P.S. I am not an Owner/ Tech as stated in
the info. iATN has not changed my info as requested. I'm
just a lowly driveability Tech. Thanks Doug M. :-) )



___________________ TEST AND REPAIR DATA ___________________

MANIFOLD VACUUM READINGS

Idle:   17 in.
Cruise: 19 in.

COMPUTER CODES AND DESCRIPTIONS

P0300- Multiple Cyl. Misfire
P1406- EGR Pintle Position Error
P0157- HO2S Bank 2 low voltage #2
P0151- HO2S Bank 2 low voltage #1

TESTING AND RESULTS

Fuel Pressure - KOEO 65psi, KOER 63psi, flows 3/4 pint in 15 sec, holds static pressure
Injector Balance - 9 psi drop exactly per injector

RELATED REPAIR HISTORY

New plugs, cap, rotor, PCV, fuel pump, strainer, filter,
crank sensor

_______________________________________________________
iATN Industry Sponsors: http://www.iatn.net/atn/
iATN WebSite:   http://members.iatn.net/index.asp
Guidelines:     http://www.iatn.net/guide.html
To configure or cancel your iATN account see:
http://members.iatn.net/config/index.asp


The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org