Perry Mick wrote:
Paul wrote:
Perry Mick wrote:
Paul wrote:
It occured to me Perry that an some sort of inflatable lip around
the duct entrance would improve the low speed thrust and could be
deflated to reduce the high speed drag.
The duct inlet, fan-plane, and exit areas are designed to be optimum
at 200mph. The question is, do I have the HP and low enough drag
to get to that speed.
That is always the big question with the ducted fan Perry.
Usually what happens is the duct adds enough high speed drag to
counteract its advantages at low speed. It is not a "broad band
device" to borrow a term from electronic communications.
Your duct is obviously designed for low speed thrust
because of the large inlet lip radius. A low pressure
is developed on this lip that adds to the thrust at
low speeds. At high speeds the lip adds to the drag.
>From the intro to Piolenc's book, I just cut and pasted from their
webpage:
In this book, we will assume a speed range of 0-200 knots roughly.
This allows us to design for cruise - which we must do in order to
avoid a stiff drag penalty - while still ending up with a fixed
duct geometry that can achieve decent static thrust.
--end of quote--
My duct wasn't designed for low speed thrust. It was
was actually designed using Piolenc's formulas for a
cruise of 200mph. But I'm finding the low speed and static
performance improved over the unducted prop. It >looks< like
a real low-speed type duct because the inlet diameter is so large.
But that is because I had a required inlet area of 1407 sq. inches,
but had to add 540 sq. inches to that, because that is the cross-
sectional area loss of the fuselage (engine cowling actually)
at the flight station of the duct leading edge. 1407 + 540 sq.
inches, doing the reverse calculation gives you a diameter of 49.8
inches. The swept area of the prop is 1054 sq. inches. Fan diameter
37.5 inches. The exit area is 1307 sq. inches, for an exit diameter
of 40.8 inches. At a cruise of 200mph, airflow through the fan is
267mph, engine rpm is 6100. (If I can get there).
There is still the situation of the direct drive small
diameter prop fan running at the same RPM. Perhaps a duct
is better in that situation.
My experience so far is that this is the case. I'm also worried about
so much of the incoming air to the small diameter prop being blocked
by the fuselage, small as it is. The free-stream at 200mph will
probably just whiz right by the prop, can't make that little turn
after the engine cowl into the prop.
The duct is capturing the air from a large diamter and funneling it
in to the prop.
The question is; will that duct add a lot of drag at
high speeds to prevent your getting to 200 MPH?
The answer, so far for most ducted fans that have been
tried, is; yes... it will add a lot of drag.
I would be curious to know the acceleration of your airplane.
If you could put an observer in the back seat that could
record the length of time it took to accelerate to distance
markers on the side of the runway on a calm day I could
calculate the thrust knowing the gross weight
of your airplane. I would do this with several taxi runs.
First to say 100 feet. Than the next run to say 200 feet
and so on until you built up a table of time to distance.
The aero drag and tire rolling resistance can be factored
in to get an estimate of low speed thrust as a function
of speed. You might also tow the airplane at low speeds
with a spring scale to measure the rolling resistance
which will add accuracy to the thrust calculations.
This is what the Rutans did with the Voyager to determine
if it would take off at gross weight.
I'd like to do that. I believe I'm getting around 300 lbs. of
thrust, but it would be good to verify that.
The Aircraft Rotary Engine Newsletter. Powered by Linux.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org