Subject: KIS TR-4 cooling arrangement.
From: Paul
Date: 5/30/1999, 11:31 PM
To: zz

Wschertz@aol.com wrote:

In a message dated 5/29/99 11:45:40, you wrote:


This looks to me like the way to go for the Kis TR-4.
What do you think? Do you think it will fit?
Perhaps with two NACA ducts instead of the external scoops.


Paul,
I will have to do some measurements, cause the fuselage is out at my hanger,
while I am working on the wings at home in the basement.

there is a bulkhead at station 139.5" from the forward firewall, and another
at Station 180.5 (which is the leading edge of the stab).  My memory says
that the Fuse is about 8-9" wide at that bulkhead -- I will check later this
weekend.  You have rudder cables, an idler arm, and the elevator pushrod to
worry about, but by splitting it into two rads, that is probably workable.

with respect to weight and balance, you can get some numbers off Vance
Jacqua's web site, where they did the W&B for Bill Grote's plane, which now
serves as the factory demo. Look at the newsletter area. It has a 210hp
Continental engine in it, and they had to put the battery (big) as far back
as possible to make it fit. I think the rotary might be less heavy.
(http://members.tripod.com/~vjaqua    ---- This site is maintained by Vance
Jaqua, the structural analyst behind the KIS.  He has pictures of members
progress, and some sketches for construction hints.  )  Mark Kettering, who
is selling his plane, used to have a web site
(http://daniel.aero.calpoly.edu/KIS/  --  Mark Kettering has this site, has
after market products pic's) but I don't know if it is still active.

Bill

The rads will fit fine behind the back seat with two NACA ducts in
the fuse bottom where the back seats go. Two stock 1 inch thick
24 by 18 Toyoto radiators would fit fine in a V shape with elevator
controls
running between them. The water pipes would have to
run out side the fueslage on the bottom. 

I went over to see Mark's plane he had for sale. The spar is in and the
wings
are closed and the stab is closed. The main gear is on as is the
firewall and most
bulkheads. The fuse top is not on nor are the windows in and the doors
are still
too piece. Mark said he bought it from someone else and he had to re-do
some stuff which put me off somewhat. The aileron piano hinge holes need
to be filled in and re-drilled as well as some other mistakes need to
be corrected. I discussed it with some of my composite friends at the
airport
and they thought it was too much money. A kit is usually worth more if
it is
untouched. Mark does nice work but if the wings are closed by someone
else
well????  

Mark had another TR-4 over there that was 100% carbon fiber. He got a
good
deal on some carbon fiber pre-preg so used the KIS molds to make up a
100% carbon
fiber TR-4. It is not much lighter than a glass version because the
thickness
is the same so all things fit. It is a lot stronger however.

I think Mark told me the stock windshield was 1/8 inch. I think that is
a little
on the low side. Mark said 3/16  would fit but 1/4 inch would probably
cause
fitting problems. 

The bulkhead just in back of the front seat is structural. It keeps the
sides of the fuse from bowing in during a high G pull up. this bulkhead 
looks like it would interfere with the Geo Tracker reclining seats.
Perhaps one steel brace tube from the firewall/floor joint up to the
fuse top
over the pilots and front pax's head would take some of that load. 
Not too good cosmetically but I would trade that for more comfortable 
seats. A 1/4 inch plexiglass windshield could also take some of this
tensile load if it was bolted in with a lot of bolts. I don't
think epoxy bonds too well to plexiglass. I could be wrong. Perhaps
a grove routed in the plexiglass could be locked into the fiberglass.
Kind of thinking out loud hear.

I think I would use carbon fiber & widen the longerons that run just 
under the doors and make them hollow to run wires and so fourth. 
This would stiffen the fuse sides and hopefully make that bulkhead 
behind the front seats  uneccessary. There is a conduit that runs 
along there anyway. This should not cut into the sholder room
as it is at hip level.

I third way of doing it is continue the center consol all the way
to the firewall and make it structural. This would then take most
of the vertical bending loads. Access could be by large holes in
the sides of the consol tunnel.

You could test all this by doing the picking-up-the-front-of-a-car 
test as outlined on the ACRE NL web site. I notice the load specs
are 3.9 G so perhaps the front of a car would be too much weight.

Sorry about all this airplane stuff but the KIS TR-4 looks ideal for
a four place low wing high performance rotary powered airplane.

The KIS TR-4 is fine the way it is but I guess I just cannot 
resist making "improvements" :-)

Paul Lamar
 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org