Anderson Ed wrote:
Well, I am happy to report I have now joined the ranks of those who
have torned down a 13B. Now, if I can just join the ranks of those who
have successfully put one back together - all will be well.
It took me 4 hours to get the engine off the airplane and onto
the work
bench.
It took me 3 hours to tear the 13B down, but much of that was
being painfully carefull to get all the rotor parts segregated so that
they would go back on the right rotors.
I have now spent 8 hours cleaning and inspecting the parts. The
rear rotor had baked on carbon disposits that took almost two hours to
get clean. But, part of that was not having a parts cleaner (went out
an bought one).
Well, I confirmed that the rear chamber had a coolant leak. It
was between the rear side housing and the rotor housing on the wall of
the chamber opposite the spark plugs (near the exhaust port). There was
black gooy substance (presumably a mixture of carbon and coolant) spread
approx 1 1/4 inch along the "O" ring area extending into the combustion
chamber. There was no clear indication of why the leak other than the
"O" ring failed to continue to provide a seal.
The "O" ring lands does not appear to be cracked, chiped or scratched,
the rotor housing width measures within specs including the max
permitted difference in width readings. There are no pits or sratches
on either housing that would constitute a leak path. In short, it
appears that the "O" ring simply failed to seal.
I would carefully examine those o-ring grooves with a jewler's loop
or even get them cracked checked.
It was also clear that the rear rotor runs hotter than the front rotor.
More carbon disposits and they were baked on harder than front rotor.
Seem to have more carbon build up near apex seals area than anywhere
else.
Check the oil squirter in the e-shaft for the rear rotor. Also the rear
rotor is now the front rotor and you could have had some trapped steam
vapor. Do you have a vent going to the pressure reservoir from that end
of the engine. Course it could have had something to do with the leak.
Also check the thermal valve in the nose of the e-shaft if you have
one. BTW Continental is having steam pocket problems with their
water cooled aircraft engines according to scuttle butt.
All apex seals, side seals and Oil seals were well withing spec
limits. Took me a while to figure out how they measure the apex seal
height. In Haynes book it looks like in the figure they are just
measuring the top componet of the apex seal. But, the dimension
measured turns out to be way too small, unless the lower part of the two
piece apex seal is included.
Ed are you sure that is not a three piece seal? Three piece have upper
and lower and a triangular end.
Then because they each have a bevel on
the touching edges, it gets tricky trying to hold the two pieces
together and then while holding them get the micrometer positioned to
the correct part of the assembly and measure it. But, finally figured
it out.
Bob G- you have to include both pieces of the apex seal and match the
two halfs the correct way and then measure across the middle of its
length (smallest distance across both pieces together). Because of the
beveled edges the top part will want to side across the bottom part.
Hey guys, tell me they are suppose to have beveled edges where the two
parts of the apex seal contact each other. The top apex seals have a
bevel as well - presumably to skim across the rotor housing better.
Yes they are beveled there but the top should be simi-circular in shape.
Rotor side seals all at or near the "new" limit. So apparently the short
amount of time on the engine with the lower 2 cycle oil mixture I was
initially running did not appear to do any damage.
The rear, center and front side housings all measured within specs on
warpage and wear. Actually the rear side housing appears to be the best
of the lot. No corrosion evident in the coolant passages. Looking at
the two exhaust ports from the outside. The front rotor port was a
light tan color while the rear one was a darker tan cooler and had signs
of coolant having settle between the exhaust flange and housing. The
two rotor housings have some mild scuffing at the high points, but no
beveling of the edges, chrome flaking or deep scores. Very light carbon
build up, just one application of oven cleaner and a wipe and it was
gone.
Eccentric shaft looks perfect - what a hunk of metal. I am debating
about whether perhaps to insert a weber jet in the oil jet for the rear
housing and leave the front one along. Perhaps more oil flow to the
rear rotor would keep it cooler where as the front rotor seems to run
cool enough as is. That way be less tendency for oil pressure to drop
off a lower rpms than if I weber jetted both.
Boy, am sure glad I got the mazda box to keep the 66 pieces off of a
single rotor separated and organized. Don't ever drop the box!!!
So, the next step is to get an order together for the parts I need to
reassemble the engine it looks like a gasket set and the Oil and
Coolant "O" rings along with the rear and front oil seals and also an
oil pump chain. Mine measured 1/2" of slack vice the 3/8" you mention
as a maximum.
Don't forget the Hayes Rotary Engineering teflon coated water O-rings
Ed.
However, I have one question that I could not find in the spec
section. How deep should the coolant "O" ring groove be? I measured it
on the rear side housing to be .070" deep. On the other housings it ran
closer to 0.065" deep. Clearly any grinding of the side housings would
tend to lessen the depth of the "O" ring groove. I would be interested
in finding out what a new housings "O" ring groove's depth would be.
Bruce T's tape made the job soooo much easier and covered some areas
that none of the books do. So thanks a bunch, Bruce.
FYI my inner coolant "O" rings all had a steel liner (thin metal strip
in "O" ring groove along with the "O" ring.
Yes early engines had that strip. I think they did away with it in
latter
engines but I could be wrong. What year is your engine again Ed? 1989?
Do you see white strips on the red coolant O-rings?
I took some photos of the process and appearance of the componets and am
trying to find a place that will digitize them so I can send to paul to
put on the list.
So, now that I have lost my cherry, the wankel actually is a simple
engine to get into. Just all the rotor parts take some getting use to
especially when some parts such as the side springs are about the size
of a thick human hair.
I must say that of the three phases, 1. taking engine off aircraft, 2.
Disassembly engine and 3. Cleaning parts. The disassembly of the engine
was the quickest and easiest. Cleaning parts was the hardest and took
the most time.
In any case, I can see no reason not to put new seals in and button her
back up.
Ed Anderson
Vienna VA
The Aircraft Rotary Engine Newsletter. Powered by Linux.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org