Subject: Chuck Harberts three rotor fuel System.
From: Paul
Date: 6/2/1999, 8:00 PM
To: zz

Chuck_Harbert@arkwright.com wrote:

Paul, at Jeff's suggestion, I guess I should pass on how I did my fuel system so
everybody can give me their thoughts. Since it's very obvious that fuel
starvation is a big risk to experimentals, especially first flights, I spent a
lot of time discussing this with others to get (steal) the best ideas (I hope).

The Velocity uses 2-30 gal. wing strake tanks which gravity feed into a 6 gal.
sump tank behind the back seat that is below the level of the strakes. There are
no valves to isolate one tank from the other. All of the 3 tanks are gang vented
into a 3/8" line to the bottom of the plane in a low (positive/ice free)
pressure area, plus I installed a vacuum breaker (low pressure check valve) at
the highest point inside the plane.

>From the sump tank, the fuel goes thru a 3/8" line/hose to a Fram high flow
racing fuel filter, then thru a fuel flow measuring device, then to either of
the 2 fuel pumps that are in parallel with appropriate check valves(only one
runs at a time). I used aircraft spec pumps sized for a 350 hp 540" Lyco
obtained from Airflow Performance (new $300). These are mounted at the lowest
point of the firewall in the engine compartment. The fuel is pumped thru a std
GM fuel injection filter to the primary fuel rail, then to the secondary fuel
rail. The return fuel goes back to the inlet line just behind the fuel flow
device, but I have plans to use a electrical diverter switch to dump it back
into the sump tank (to avoid vapor lock due to overheated fuel), but I'll lose
my fuel totalizer (but not flow volume).

I used the stock Mazda  20B vacuum controlled fuel rail pressure regulator which
varies the rail pressure from about 25psi at high vacuum (idle/low loads) to
about 50 psi under full boost 8-10 psi. So far the system has operated very
well, but it hasn't been in the air yet. The engine runs very smoothly at all
rpms, even with high engine temps (220 degF) and with the cowls in place.

I also have a dual independant battery system because of the dependence on
electrical power for the fuel pumps and electronic ignition. I also have 2
independant electrical paths to the pumps and electronic  ignition which I check
as part of the preflight. I probably should run a load test to see how long the
engine will continue to run on one battery only (alternator out), so I can know
how much time I have before I must land.

 As I understand it the biggest problem with fuel tanks is to get proper venting
so that the tanks empty evenly. Bryan's problem may be a venting problem, but I
can't tell based upon his limited description of a "visible sight gage". The std
Velocity/Long E fuel gage is a 3/8" vertical plastic tube that is connected to
pipe fittings in the top and bottom of the strake tank. I didn't like this idea
because of the accidental chance of ripping it open inside the cabin, but it's
in most of these planes and seems to work fine. I used instead a mechanical
direct reading guage that uses a float. It is attached to the side of the stake
tank inside the cabin, but there is no fuel inside the guage/cabin (magnetically
driven). It's p/n 05-16700 from Aircraft Spuce ($40 each). It's designed for a
aluminum airplane, but it wasn't hat hard to adaft to fiberglas. It's very
accurate and reliable. I also have an elec low fuel warning light on the panel
that is a connected to a float inside the sump tank at the 4 gallon level.

p.s. I agree with Paul that Bryan needs to find out why he's getting bad
readings before he flies again.


 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org