Subject: Another choice of PSRU for 13B - Larry Neal/New Horizons Components (Boyd, Texas)
From: Paul
Date: 6/23/1999, 10:01 PM
To: zz

David Carter wrote:

I sent the attached/forwarded e-mail to the wrong address so am
forwarding it to both the rotary engine list and RV list.  Sorry for the
extra bandwidth.

David Carter, RV-6 QB, Nederland, Texas



This e-mail is just to pass on some new info (to me) which I haven't
seen any reference to since I've been on the e-mail list in Feb 99.

Was going through old Sport Aviation and Experimenter magazines tearing
out articles to file in my hard-copy archives.  In Apr '97 Experimenter,
pg. 10, I found a picture of a planetary gear reduction drive that is
being used on Mazda 13Bs in Air Command Gyrocopters and on Subarus.
As of 1997 it weighed 40# and cost $2500, had 4 reduction ratios:  1.84
and 2.18 (run "backwards") and 2.84 and 3.18 (run forward).  

I got the
new area code and called New Horizons Components, 813 East Rock Island
Avenue, Boyd, Texas 76023, (940) 433-2007.     

Reached the owner Larry Neal:  
Hihest hp so far is 280hp 6 cyl Subaru.  Several have been flying
on Air Command gyrocopters.  He uses a Chrysler 904 planetary set (4,
not 3 [pinions] as in Ross).  

Some Ross's are three pinions most are four. You can get a six pinion
set off the shelf used for drag racing that will fit the Ford C6
planetary set used in the Ross PSRU. PL

He has the unit working fine with no problems.  Now
he's going to produce a model with prop shaft 2 1/2 inches longer so as
to accomodate a mechanism that will manually control pitch of a 3 blade
Warp drive prop through a  plus or minus 37 degree pitch range.  Even
without using that prop, I think the extra prop extension is in the
"right" direction (forward) to reduce drag and increase prop efficiency,
as well as help on RV-6 CG.


 I then surfed the net to www.rotorcraft.com and clicked on Air Command
Gyrocopters and found their telephone in Caddo Mills (?), Texas,
903-527-3335.  Reached the ultralight demo pilot who was working late
with some others.  He's not a certificated pilot and has not piloted the
Mazda/Neal combination but has flown in the gyrocopter and listens to
the others.  People like it better than the Ross for at least 1 reason:

It doesn't have the slow idle RPM "chatter" in the gear box.  The PSRU
uses a Sprague (?) clutch that only drives the prop forward. 

Actually it uses four sprague clutchs for durability as I recall. PL


If the
engine or resonance tries to kick back, there is nothing to kick - the
prop would freewheel if engine/PSRU tried to run backwards.  Also, they
say the workmanship and craftmanship is superb.


I can confirm this. PL

  I like the idea of having the 2.84:1 ratio - my feeling about power vs
rpm and vs altitude is that the only way to get "normal" cruise power
above 8000' is to increase rpm (if you had a controllable pitch prop) to
make up for the low manifold pressure.  With a fixed pitch prop, on the
other hand, the only way to get the ability to generate good cruise rpm
at lower manifold pressure is to go to the higher PSRU ratio, which
means you are going to be able to overspeed the prop at sea level on
takeoff and go-arounds unless you either 1) be careful, or  2) use a
modified "throttle friction type gadget" to screw out (aft from
instrument panel) to limit throttle movement - to prevent over-reving
the prop (limit yourself to less than sea level manifold pressure - no
big deal in an RV that climbs 1700 to 1900 fpm at full throttle.)  Then
as you climb, you can screw this thing in and increase the forward range
of motion of the throttle to "full open" to get what little pressure
there is at high altitude.

That's all I know - just what I read and hear from others, until I get
my own up and running.

David Carter  (dcarter@datarecall.net)

 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org