Subject: Canard motor mount and cooling.
From: Paul
Date: 7/26/1999, 1:53 PM
To: zz

X-Mozilla-Keys:                                                                                 
JF wrote:

I'm new to this game, so my comments and questions may seem niave, but here
goes:

1; Tim England did a beautiful job designing and building a V-6 powered
Velocity (Sport Aviation, May '99).  He used a Mustang style air scoop for
engine cooling.  However his performance figures seemed a little slow for the
engin power.  I can't help but wonder if that air scoop increased the drag
coefficient of the Velocity sufficiently to degrade the performance.  Any
comments?

As I recall he was quoteing rather low fuel burn so I suspect the engine
did not have as much power as he thought. Here is the formula again.
Fuel burn in gallons per hour times six divided by 0.45 equals HP.

If you want to find out how hard a person is running his engine
just ask him how many gallons per hour he is burning and then
apply this formula. The number 0.45 is the Brake Specific Fuel
Consumption (BSFC) for a gasoline burning four stroke piston engine.
A rotary is about 0.5 and a two cycle is about 0.65. A diesel is about 
0.38. These numbers are based on the average results of testing 
millons of engines. If some one tells you his engine is generating
200 HP and he is burning eight gallons an hour take it with a grain
of salt.

This is all not to say that a P51 type scoop does not add drag.
It most certainly does.


2; The E-Racer design uses an NACA bottom inlet duct with a horizontal bottom
location radiator similar to your design.  It seems that a sufficiently large
enough NACA inlet duct would create less drag than a scoop.  How about NACA
inlet ducts?  Wow well do they perform?  Could a Velocity be modified to use a
NACA type duct as on the E-Racer?

Yes. My only question is if a horzontal  rad is too close to the NACA 
duct I don't know how well that would work as the NACA duct is designed
to roll up the boundry layer and provide an internal airstream
parallel to the direction of flight and not at right angles to it,
if you get my drift. I also don't know what pressure the NACA type
scoop can work into. I suspect it will stop working at some
pressure well below dynamic pressure or not too far above
static pressure. 

A P51 type scoop on the other hand would merely pressurizes the
chamber below the horzontally mounted radiator and above 
the scoop with dynamic pressure if, for some reason,
the radiator became completely plugged up with say
....bugs or debre. 

BTW dynamic pressure is that pressure you would measure
at the center of a flat plate held perpendicular to the
airstream. The pressure in pounds per square foot is 
0.0026 times velocity in MPH squared. Static pressure is
15 pounds per square inch at sea level and reduces
with altitude of course.

I would say the NACA duct might work if it was well
ahead of the horzontally mounted, low aero pressure drop 
(thin), radiator and probably provide less aerodynamic drag. 
You would of course then have to cut into the 
rear seat area/volume of the canard to install the NACA duct.

This is just another illustration of why large frontal area thin
rads are lower drag than small frontal area thick rads. Thin rads
are now universally used in cars and trucks.


3; Regarding cooling while setting on the ground:  On a Velocity, it seems a
small NACA outlet duct on each side of the engine cowling might work well.
Airflow over the cowling created by the prop would certainly create a partial
vacuum and reasonable air flow.  The duct could have an inside offset bottom
plate an inch or two deep to prevent water from entering the engine
compartment.

I think you would be just as well off with a large hole in the back
as is usually done with pushers. A fan or water dribble would be 
a better bet IMHO.


What are the problems with this arrangement?

Would such an arrangement cause sufficient turbulence in front of the prop to
reduce airflow/prop efficiency?

Pusher canards have enough problems in this regard with the wing and the
cowl
so a little more would probably be hardly noticed.


Best regards;

James Freeman

Don't forget... today is my last day for awhile.

Paul Lamar
 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org