Subject: 35k Rotary Attempts and turbocharger matching.
From: Paul
Date: 8/9/1999, 2:35 PM
To: zz

X-Mozilla-Keys:                                                                                 
Russell Kent wrote:

Brian D. Cain wrote:

Although I'm no scientist, I believe the term you guys are hunting for,
rather the equation you're looking for, is "(x) density in a given volume".

I would agree with Russell that, although ambient air temperature at
(x) thousand ft. may be much lower than at sea level, the density of the
air in a given volume is also much less.

That is precisely what I was saying.

I believe the goal, as it is in a combustion chamber, is to have as dense
an amount of mass air as possible; preferrably leaning on the temperature
and not pressure side.  This is the main and only reason why I use an air
to water intercooler system in my Rx7 for lowering intake charge
temperatures efficiently.  I'm not sure if this is an option in an aircraft,
however, because of the added complexity and potential weight.

This is not where I was going, though.  I was referring to the engine's ability to
shed the heat.  Recall that the rotary's major stumbling block is heat rejection.
That heat is shed through the radiator into the cooling air, and the rate of heat
rejection is a function of many things, including the thermal capacity of the
working fluid.  In this case, we're talking about air that is roughly 40% less
dense than sea level.  This means (all other things being equal) that the radiator
has to pass 40% more air per minute to have the same cooling effectiveness.  If
you keep the same size radiator as one used at lower altitudes, then the air flow
goes up 40%.  That kind of increase is likely to cause a conversion from internal
diffusion to external diffusion, which (as was discussed earlier on this list) is
a Bad Thing.

Now in reality, all other things *aren't* equal:  the air is much cooler, so the
heat transfer rate is increased by the larger delta T, and reduced by the lower
thermal capacity of the working fluid.  But I still think you're likely to need
substantially more airflow through the radiators in order to shed the waste heat,
and that increase in air volume per minute is going to play hell with your ducting
and the radiator's surface area.

Paul wrote:

So what you are saying is it will be easy to heat the cabin and the air coming
out of the turbo charger and into the intercooler will be hotter than I think?

That's not precisely what I meant.  True, the cabin air will take fewer calories
(or BTUs) to warm by virtue of the fact that the volume is constant and the
pressure reduced, therefore lower thermal mass.  But all those small cracks that
leaked "little breezes" before are now going to be "arctic jets".  Better make
darn sure the cabin is tight.  Also, the CTE effects can make new leaks appear.

The temperature of the intake air between the compressor (half of the
turbocharger) and the intercooler isn't the issue I was raising.  Presumably the
compressor's pressure-induced delta T is relatively constant (or perhaps linearly
proportional) regardless of altitude.  The problem is the intercooler's ability to
shed the heat is affected by all the factors monkeying around with the engine's
radiator (volume per minute versus delta T).  A turbocharged engine that runs fine
at 10K could end up detonating itself into oblivion at 35K because of the
intercooler's inability to cool the intake charge.

I don't even want to think about what -50 deg C is going to do to all of the
various electrical and fuel lines & connectors.  Remember how warm some of those
electrical devices get in the panel?  Imagine how warm they could get if the air
is too thin to effectively convect the heat away.  And when you make a descent
into warmer, moister air, you could condense all over the innards.  Might want to
keep those vacuum-powered instruments.

I could be overestimating the problems, but I certainly would want to look at
things very carefully first.  I'm certain that Jeff Spitzer can explain all sorts
of high-altitude issues and how they can be addressed.

Jeff, tell us about the cooling issues on your high-altitude UAV.

The only good news is that the risk of an in-flight engine fire is about zero.
:-)

Another excellent point. It looks more and more like we
need a computer simulation.

Yes, it would help highlight where the problems are going to be.

Russell Kent


The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org