Subject: PSRU Preload & New PSRU design
From: Paul
Date: 9/4/1999, 4:50 PM
To: zz

X-Mozilla-Keys:                                                                                 
Bill Freeman wrote:

Paul,

It lliks like the only place to set the preload on the bearings
is by shims under the bearings or between the main baseplate
and the carrier or carrier and 'snout'.  Would a screw adjustment
at one end be a good idea to set the preload, like snug it up tightly
to seat everything, back off the nut to free spinning, then torque to
a specific value calculated to do the preload? 

I thought a lot about it Bill and I would like to avoid threading
the prop shaft. Threads are like built in cracks unless you
step the diameter and relieve everything. Gets expensive.
The best place is out beyond the prop flange and that means
splining the prop hub which is its own can of worms.
Shims look like the easy way. The big question in my mind is
how often will they need to be reset. Modern wheel bearings
seem to go for ever. 

Here is a far out trick for you to think about Bill.
How about a large diameter Belleville washer in front of the
forward  bearing cone? Behind the prop flange?
In a tractor version there is little load on this cone as 
the aft bearing takes the prop thrust. Mainly the Belleville
spring would be to take up the thermal slack. 

How do I calculate the spring rate and stress on 
a Belleville spring? For instruments these are usually made
from AISI C1095 spring steel. One Belleville spring .75 ID 
1.5 OD 0.072 thick will generate 1180 pounds of thrust flat.
Ours of course would be 3" ID 3.5 " OD. 

 BTW, I *do* like the
use of tubes for bracing the snout.  Assume six 1/2" OD by
0.035 wall 4130, lots of strength.  You want to machine pairs
of mounting ears so the ends are loaded in double shear.  This
design will have a MUCH better strength to wt than the typical
set of relatively shallow aluminum fins, plus the higher modulus 
of steel  helps stiffen the system a lot.

I was thinking of using 1/2 inch square tube with a single
7/16" thick or so aluminum lug. Bearing stress in the tube
walls could be overcome with welded on washers.


Still wonder about the flange attach to the mainshaft/tube.
Not too excited about furnace brazing, QA is an issue as is
field inspection, i.e. how can you tell if it is failing??
What about light shrink fit and a series of countersunk AN509-8
screws, say two rows of 8, with the rows staggered?  Use
MS21042 metal stop nuts on the inside. Ignoring the
friction (conservative assumption) the bolts should handle
at least 12000 lbs in shear, and at a 1.5" radius this is
18000 in-lb or 1500 ft-lb.  This is based on a guesstimate of
the minor diameter of a -8 screw as I don't have my reference
books here at home. My guess is that the max
torque you'll actually see is in the 250 ft-lb range.
This, of course, would be the worst case with all the
screws just finger tight.  In reality, the friction will carry the
 load and the bolts will just keep the normal force high
enough to make the friction coefficient very high.
You can use a long wrench to check the torque on the
nuts at each annual to validate the flange/mainshaft security.

Bill

Sounds like a good idea Bill. A soft washer under the nut
could accommodate the inner diameter. I think Ross uses 
just a couple of pins and gets away with it.

Modern high speed, high HP NC lathes could hog this out of
4340 billet in a blink. Powersport has these kinds of machine
tools if I can talk them into making parts for me. This shaft
is very close to their design. We both use the same method
to attach the bull gear to the prop shaft.

Paul Lamar
 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org