Subject: Chuck's latest experience with turbo 20B
From: Paul
Date: 10/21/1999, 1:44 PM
To: zz

X-Mozilla-Keys:                                                                                 
charles.harbert@fmglobal.com wrote:

Paul, you haven't heard from me on my project for awhile because I had an
inflight fire a few weeks ago. Fortunately, it occurred during takeoff and the
tower called me imediately. The engine kept running and I was able to do a 180
and land safely. Because I'm at a 10K' runway, towered airport with an
on-airport fire station, I was able to taxi right up to them. The fire had gone
out (because all the oil was pumped out of the engine) by then. The plane and
engine had very little damage and I expect to be back flying next week.

I decided to tell everyone what happened so that maybe they can learn something
from my experience. Because I was still having oil cooling problems, I installed
a 3rd oil cooler (5.5"x 11"x 1.25") in front of my lower (belly) radiator. I got
it from Griffin who is a well respected mfg of radiators. It's made out of
aluminum and good for 300psi. I had about an hour of operating time on it
including the previous flight. It split open (about 1'circular) near one of the
fittings and sprayed oil into the radiator above. Since the airflow is up and
then out the back on a Velocity, the oil was carried over towards the exhaust
manifold and turbo exhaust pipe.

According to an eyewitness, I was spraying a mist of oil out the back during my
takeoff roll and as I rotated a ball of flame came out the back. it continued to
burn on the exhaust side off the engine until I was aware of what was happening,
when I throttled back and turned back to the field. I did feel a surge shortly
after t/o which probably was the start of the flame. The engine did continue to
run normally, but I did get an engine monitor alarm (red light-low oil pres and
hi under cowl temp).

The main ignition point was the turbo exhaust pipe which is very aft in the
plane which helped because the flames and heat went out the back rather than
burning inside. I did have some smaller burning in the forward part of the
engine where the exhaust manifold ignited some of the oil vapor. I'm replacing
some wiring and plastic tubing that melted. I had the wiring for the injectors
inside of spiral plastic tubing which kept it from melting and allowed the
engine controller to continue to operate (did not short/grd out). The inside of
my fiberglas cowlings is painted with Ocean fire retardant paint which prevented
them from being damaged (or catching fire). I used some black foam insulating
material which burned readily and I'm removing it from the plane. I have high
pressure fire resistive 3/8" hose for fuel lines and it survived well, but will
be replaced and covered with the orange fire proof hose (can't remember name).

It appears that the oil cooler may have been damaged in shipment, as the
original box showed damage on a corner. I don't remember seeing this when I
opened the box, and it looked fine and didn't leak during initial operation. It
must have weakened the thin aluminum and the oil pressure split it open. I will
personally pressure test the replacement oil cooler to 300 psi before I install
it, as well as inspect closely for shipping damage. I had just added Pro Blend
(anti friction additive) to the engine which I used for yrs in our race engines
which I believe protected the engine. Oil pressure and engine operating
parameters are normal, and the oil filter was clean.

I was making a test flight to see if my Ross gearbox oil temps were lower. I had
been getting a 50-60 degF rise while flying which is too much (indicating metal
to metal friction). I had installed an internal oil spray system to directly oil
the sun gear which I believe to be the problem with the std splash oiling
system. Others have dropped their gearbox temp with a similar system. I was not
able to determine if this fix was successful, but I'll report later when I get
back in the air.

Needless to say, I learned a lot from this, and I'll be doing a lot of checking
and double checking before I fly again. This was my 7th flight, but it wasn't
very lucky.

Chuck
 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org