Subject: Herring bone cog belts PSRU's
From: Paul
Date: 11/18/1999, 8:41 AM
To: zz

X-Mozilla-Keys:                                                                                 

Matthew Cosman wrote:

      There are two simple variables on this type of drive.  Belt
width(determines belt contact area under load, and belt srtength) Pulley
dia.(determins force seen by belt  i.e. 1 ft/lb of torque = 1lb of tension
on belt for 12" pulley)  Pretty simple but what I need to know is shaft
torque, not HP ,Dont shoot :-),I am positive that there is a place where
these two variables meet on this application.  I have seen 5" pulleys that
will take 300 ft/lb's of torque. A 7" belt of the right construction will
take 750lb of working tension.(someone check my math it's late).  Also the
longer the belt the longer it will last ( that is linear too).  There is
half a dozen more desighn considerations ( shaft separation,  static
tension,  mass factor,  slack side tension, etc.)  Let me know what the
torque is and I'll find some combination.  let me know what ya'll think
    thanks

Takeing some numbers from Jim Medera I think he said he was getting 900
HP
at 8500 RPM. As I recall the formula for torque is RPM X Torque / 5252
is
HP. So Torque is HP X 5252 / RPM = TORQUE.

560 ft lbs looks about right. A six inch pulley would be 1120
pounds of tension and at about 107 pounds per inch we would need
a 10.75 inch belt. The orginal ten inch was just a guess on my part but
my guess was not that far off. Maybe I need to add a couple of inches
of belt width and get up to 12 inches. Particularly for the
upper engine as the belt is shorter there. We need to recalculate
for a five and four inch pulley. Maybe we can cheat on belt
tension. Perhaps we need to get one and load it up.

Here is a little quick and dirty chart of Torque verses RPM
and HP I proged up in QB.

RPM>   4500 5000 5500 6000 6500 7000 7500 8000 8500 9000 9500 10000
 HP
100   117  105   95   88   81   75   70   66   62   58   55   53
150   175  158  143  131  121  113  105   98   93   88   83   79
200   233  210  191  175  162  150  140  131  124  117  111  105
250   292  263  239  219  202  188  175  164  154  146  138  131
300   350  315  286  263  242  225  210  197  185  175  166  158
350   408  368  334  306  283  263  245  230  216  204  193  184
400   467  420  382  350  323  300  280  263  247  233  221  210
450   525  473  430  394  364  338  315  295  278  263  249  236
500   584  525  477  438  404  375  350  328  309  292  276  263
550   642  578  525  481  444  413  385  361  340  321  304  289
600   700  630  573  525  485  450  420  394  371  350  332  315
650   759  683  621  569  525  488  455  427  402  379  359  341
700   817  735  668  613  566  525  490  460  433  408  387  368
750   875  788  716  657  606  563  525  492  463  438  415  394
800   934  840  764  700  646  600  560  525  494  467  442  420
850   992  893  812  744  687  638  595  558  525  496  470  446
900  1050  945  859  788  727  675  630  591  556  525  498  473
950  1109  998  907  832  768  713  665  624  587  554  525  499
1000  1167 1050  955  875  808  750  700  657  618  584  553  525


Paul Lamar

Matthew Cosman wrote:

Unfortunatly I just found out that the PD is rated at 500HP @ 200rpm.  This
is the largest stock PD part.  If we wanted something higher we would have
to go direct and see if they will in fact make something custom.  I guess
there is not a very big market for the kind of belt we are talking about.
someone mentioned machining our own HOT pulley?

You have considered two or more belts side by side Matthew?

Paul Lamar
 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org