Subject: COZY firewall rubber mounts.
From: Paul
Date: 11/25/1999, 8:51 AM
To: zz

Bulent Aliev wrote:

This builder moved the rubber mounts on the firewall as you suggested
Paul.

    ---------------------------------------------------------------

Subject: RE: COZY: RE:Auto Engines
Date: Thu, 25 Nov 1999 08:48:21 -0500
From: "Johnson, Phillip" <phillip.johnson@lmco.com>
To: "'John Slade'" <rjslade@bellsouth.net>,
     "'Cozy'" <Cozy_builders@canard.com>

John Slade Wrote>One thing you didn't mention was mounting issues.
Any comments on that? <end

With the vibration of a six cylinder horizontally opposed engine revving in
excess of 4000rpm the vibration is very low and I had no knowledge of the
dynamic mass of the engine, PRSU, and propeller so Dynafocal mounts were out.

(BTW Dynafocal mounts only work for a specific engine prop configuration, add
an extension and you can forget it.) I made a mount that was rigidly mounted
to the engine but had Lycoming conical mounting rubbers at the firewall.
Instead of the hard points on the firewall I fabricated a cup to hold the
Lyc. rubber mounts so that the whole firewall backwards arrangement was
suspended by the rubber mounts. With this configuration there is no
differential movement between the engine and any of the accessories. The
mounts attach to the firewall as follows:

1) The lower two mounts are in the stock position on the firewall,
2) The second pair are mounted just under the spar and about three inches
inboard of the lower mounts.
3) The third pair of mounts mount high up on the firewall.

Originally the top mounts were in the stock position and I hung the engine
off a dummy firewall. It looked so wrong and I was not prepared to fly with
that configuration so I moved the mounts upwards. Now to do all of this I had
to do some structural analysis, in particular for the upper pair of mounts. I
provided somewhat of an overkill for the upper mounts just for safety and to
provide for additional roll over protection at the rear of the fuselage. It's
not possible to describe the engine mounting frame other to say that it is
configured as two frames, one bed mount under the engine and one, dominantly
tensile, frame above the engine. The main loads from the prop are
transitioned to the bell housing of the PSRU and from there directly to the
firewall. The engine does not see the prop load at all. If enough people are
interested I guess I could create an info pack of sketches for email but you
must all appreciate that it is still experimental and subject to change.

Phillip Johnson

Cozy MkIV RG EG33  #30



This is interesting. Great minds....... :-)

The Lycoming conical mounts would take more fabrication than the
Barry mounts I mention in the ACRE NL web site drawings. That is why
he had to "fabricated a cup to hold the Lyc. rubber mounts"
The Barry mounts will work in a simple hole in a 5/8 to 3/4 thick
firewall. They are also lots lower cost than the Lyc mounts. 

Also the middle mounts mentioned are probably redundant. They
would not hurt other than weight, cost and time  but they don't carry 
a lot of load either either unless the upper fuselage structure 
is very weak.

If you move the mounts on the firewall from the place the designer
of the aircraft choose you need to beef up the connection of the
firewall to the fuselage skin. In the case of a Cozy there probably
are some longerons running about spar level forward under the
canopy. Just above the point where those longerons intersect the 
firewall are the best places for the upper mounts. The fuselage 
structure much above that could be beefed up with extra laminates 
to transfer the loads down and forward to those longerons. In that
case the top mounts could be moved further up.

In any event keep the mounts as close to the fuselage skin as possible
and as far apart as possible.

Another problem with retractable main landing gear pushers that retract
into
the fuselage is; the fuselage strength  under the spar is compromised.
Carefull consideration needs to be applied and this area needs beefing
up as well.

Paul Lamar
 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org