Subject: Aluminum end housing detonation gun coatings.
From: Paul
Date: 2/9/2000, 8:31 AM

MATERIAL COATING BY THE DETONATION GUN PROCESS 

There are numerous methods available to repair compressor and turbine shafts when
bearing journals, seal surfaces and other critical areas require resurfacing. One of
these methods is by the use of
detonation gun coatings. The detonation gun is a device that can deposit a variety of
metallic and ceramic coating materials at supersonic velocities onto a work piece by
controlled detonation of
oxygen-acetylene gas mixtures. Coatings applied by this method are characterized by
high bond strength, low porosity and high modulus of rupture. This paper describes
the equipment used to apply
D-Gun coatings and provides data on coating thicknesses used, surface finishes
available and physical properties of some popular D-Gun coatings used in machinery
repair. Examples are cited
showing increases in operating life that can be achieved on various pieces of
equipment by properly selected and applied coatings. 

Author: 

     Walter Wolentarski, Engineering Associate, Linde Division, Union Carbine
Corporation, Tonawanda, New York 

Subject: 

     Repair 

11th; page 217; 1982

A-Flame Metal Spraying Systems & Replacement Parts
              for Arc, Flamespray, Plasma, ABB Robots & Detonation
                               Gun Technology




                 .......A-Flame manufactures complete Arc Spray, Flame Spray,
                 Plasma Spray, Detonation Gun Systems, and component repair
                 parts. We have been in this business since 1978. We stock a
                 complete line of interchangeable replacement parts for several
                 manufacturers' systems, as well as masking tape, powders, and
                 wire alloy. 

                 . . . . . . . . . . . . . . . . . . . NEW! . . . . . . . . . . . . .
. . . . . . . . 

                 .......A-Flame Corporation is the newest center for ABB Robotics.
                 It is our intention to be the low cost supplier of robots,
turntables,
                 and work handling systems in the materials industry. Regardless of
                 size, call, e-mail, or fax us your project needs, or your request
for
                 quotation! 

                 ...........................NEWEST
PRODUCT!................................. 

                 .......The new DS-2 Plasma Control Console is designed to perfectly
                 replace all old Metco 7MC plasma consoles, without changing any
                 spray parameters, or changing the operator's methods. It is a great
                 way to upgrade the older 2M and 3M systems, with the newer
                 ramp up/down feature. It is quite possible to disconnect your old
                 console, roll the DS-2 into place, and reconnect the power supply,
                 powder feeder, water chiller, plasma gun, and begin spraying. The
                 operation will be identical, except that you will now have all brand
                 new controls. 

                 . . . . . . . . . . . . . . . . . . . NEW! . . . . . . . . . . . . .
. . . . . . . . 

                 .......A-Flame now offers a complete Detonation Gun System,
                 including an integral powder feeder. 

                 .......It operates on as little as 115 volts and 200 watts of power,
                 consumes 1/10th to 1/3rd the gas of the most efficient HVOF
                 system, at gas inlet pressures of 10 - 30 psi (70-210 kPa); yet, it
                 provides a coating that exceeds the best that standard HVOF can
                 offer, with coating adhesion up to 36,250 psi, and porosity in the
                 range of 0.1 - 1 percent. 

                 .......You can grit blast the surface of the part, using the same
gun
                 barrel that is used for the coating process. There is no need to
have
                 extra grit blasting equipment. The Gun has no moving parts, and it
                 has no parts which can wear out, similar to the Laval nozzle in the
                 HVOF gun, no valves, and no Electrodrive Motor. 

                 .......Due to the low amount of heat transferred to the gun barrel,
a
                 special water chilling cooling system is not needed, water
                 consumption is very low (1 gpm), and heat transfer to the substrate
                 is very low, at 100-150C maximum; and, if necessary, the heat
                 transferred, can be maintained at room temperature, making
                 possible the spraying of precision components, such as crankshafts,
                 turbine blades, or thin films, without the danger of causing thermal
                 deformations or chemical changes. This makes it possible to spray
                 low melting point materials, such as plastics. 

                 .......WILL YOUR PRESENT PROCESS REMAIN
                 ..............................COMPETITIVE? 

                 .......PROBABLY NOT!...Who are the major WORLDWIDE spray
                 shops? What technologies are they using NOW? Is it possible, that
                 within 5 years, one of these major sprayers will have an additional
                 115 new WORLDWIDE facilities, using the lowest cost process,
                 and producing the highest quality coatings? Ask yourself, who is
                 currently the lowest cost producer, providing the highest quality
                 coatings? 

                 .......YOU CAN COMPETE, IF YOU EMBRACE CHANGE! No
                 matter your worldwide location, if your process uses less electrical
                 energy, if it uses less gas, if it requires almost no consumable
parts,
                 if it is ready for production 97% of the time, if it requires only
one
                 person to operate and maintain, if maintenance consists of only
                 minor cleaning, if your scrap rate is greatly reduced (no nozzle to
                 spit copper); AND, if your process produces the highest quality
                 coating, of all the available processes (FROM STANDARD
                 POWDERS); then, you will definitely be able to compete with the
                 largest and most knowledgeable people in your industry. 

                 .......Your process needs may be for an in-house production line;
or,
                 they may be for a multi-process spraying facility, which contracts
                 for many different spraying applications each year. Perhaps you are
                 a systems integrator, or consultant, helping your customers to
                 improve their processes. You will need our DETONATION GUN
                 SYSTEM to enable you to remain at the peak of your industry. 

                 .......Click on the e-mail address (below), and ask us for our
                 brochure. 


                 Contact Name:
                               James E. Baker
                 Address:
                               8175 Kroger Farm Road, Cincinnati, Ohio
                               45243-1639 USA 

                 Phone:
                               1 513 831-4284
                 Fax:
                               1 513 831-5237
                 E-mail:
                               aflame@fuse.net
                 URL:
                               http://www.aflame.com

                 . . . Tom Hart or James Sword will gladly help you with your
                 replacement parts needs, and Jim Baker will eagerly answer your
                 questions about systems, components, or technical data. Just call,
                 fax, or, send us your E-Mail at: aflame@fuse.net 

                 . . . How may we be of service to you? 


 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org