-
Atomising Systems Ltd
Powders for Hard Facing and Weld
Surfacing.
Atomised metal alloy powders are widely used as a convenient form in which to supply
hard or corrosion resistant alloys to surfaces.
ASL specialise in the supply of plants for atomised powder production and have
considerable experience of the hard facing field. The principle techniques and their
applications are outlined below.
The names of the different processes are not wholly standardised and different
suppliers may have different names.
Oxy-Fuel Gas Spraying
(Flame Spraying)
Powder contained in a hopper is conveyed into a flame either by the fuel gas itself
or by a separate carrier gas. Some designs of powder spray torch also use additional
air to propel the heated particles
on to the work piece, to confine the spray and/or to provide cooling. The fuel gas
is usually acetylene but is sometimes hydrogen.
Powder grain size varies for different torch designs but is typically 40-125 microns.
Plasma Spraying
This is similar to Oxy-Fuel gas spraying in that a porous deposit is laid down on a
surface by introducing powder particles into a plasma "flame" which heats them
extremely rapidly and projects them
onto the surface. Because of the very high temperatures achievable in a plasma
(10,000°C), it is possible to deposit refractory oxides and metals if required.
A recent application of this torch is low pressure plasma spraying where the process
is carried out in an evacuable chamber under inert gas and low oxide content deposits
such as Ni-Cr-Al-Y can
be produced.
Plasma spraying is generally found to give denser deposits and heat the substrate
less compared with Oxy-Fuel gas spraying. Equipment costs are also higher so it is
normally used for aerospace and
other critical uses.
Particle size ranges for the best results are very narrow, for example 45-90 microns,
and a wide range of different specifications are used for various applications.
Spray-Fuse Process
Flame sprayed coatings are somewhat porous and their bonding to the substrate may not
be perfect. By using "self-fluxing" alloys (high in silicon and boron), it is
possible to fuse the coating in a
separate operation after spraying to give a deposit with 100% density and a
metallurgical bond to the substrate. Fusing is normally done with an oxy-acetylene
flame but for large volume production
furnace fusing or induction fusing can be used.
The particle size range used is normally 40-125 microns as for flame spraying.
.
Powder Welding
This process uses self-fluxing powders similar to those used in spray fusing. The
equipment is quite simple, being essentially an adaptation of an oxy-acetylene
welding torch with a powder hopper
and injection venturi mounted between the gas mixer and the nozzle. The powder
falls through the flame and on to the workpiece where a weld pool is maintained and a
continuous bead laid down. It
is especially used for depositing thin wear-resistant beads on the corners or edges
or moulds but can also be used for area coverage on small parts.
Powder size depends on applications: standard 20-150, 20-125 microns or 20-106
microns powders are suitable for thicker deposits while very thin deposits demand
finer powders.
Plasma Transferred ARC (PTA) Process
This process resembles powder welding in that a molten weld bead is deposited on to a
surface. Heat is provided by a plasma torch and the powder is fed through the plasma
into the weld pool. The
weld bead can be made wide by oscillating or "weaving" the head.
The process demands rather sophisticated and high cost equipment but allows very high
and consistent quality deposits to be produced at high speed. It is thus used on
very long repetition work, such
as automotive valves, where fully automatic production can be done or else on
relatively heavy deposits where high quality is essential.
High Energy Coating Methods - Detonation Gun & High
Velocity Oxy-Fuel Process
Powder particles in normal flame and plasma spraying are projected at speeds of
around 100 m/sec and form somewhat porous coatings (for example 15-20% porosity). If
the particle velocity can be
raised to much higher levels by using Hypersonic (Mach 1-3) gas velocities, then
deposit porosity can be reduced to less than 5%, even approaching 1%, with excellent
adhesion and strength. Initially
the Detonation Gun ("D-gun") was the only option which was very slow and expensive.
More recently the High Velocity Oxy-Fuel (HVOF) proces, which has lower capital and
operating costs, and
much faster deposition rates, has been developed. This has led to a rapid increase
in applications.
Alloys
A large proportion of the metallic powders used in these processes are produced by
atomisation. Some are used as atomised and screened while others may be mixed with
other materials (such as
carbides) or coated for special properties (such as Ni-Al exothermic powders).
The most common powders are probably the Ni-Cr-B-Si range of "self-fluxing" alloys
which are mostly applied by flame spraying, spray-fusing, powder welding. These
range from soft alloys
(Rc20) with chromium levels of 15-20%. These powders are produced by water and gas
atomisation.
Cobalt alloys are often used in more severely corrosive applications ("Stellites")
and these are more often gas atomised to ensure spherical particle shapes and good
powder flow properties.
Most plasma-spraying metal alloy powders are inert gas atomised as the alloys used
are often rather reactive and low oxide contents and spherical shapes are essential.
ASL offer
A wide experience of atomising techniques, both gas and water, for hard facing
powder production.
A range of standard atomising plants with outputs from a few tonnes to thousands
of tonnes per year.
Atomisation Applications Overview.
ASL Products
If you have comments or suggestions, e-mail
ASL at info@atomising.co.uk
Atomising Systems Ltd
Sheffield Science Park
Arundel Street
Sheffield
S1 2NS
England
Telephone : +44 (0)114 276 7910
Fax: +44 (0)114 273 1977
The Aircraft Rotary Engine Newsletter. Powered by Linux.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org