Subject: Housing temps and CHT's thermocouples.
From: Paul
Date: 6/5/2000, 8:24 AM


charles.harbert wrote:

Paul, I'm using the stock pump and pulleys and having no problem
cooling
the
turbo 20B engine (180-190 degF) in a pusher at over 250 hp. I not so
sure that
it's inadequate for the job.



Also, is the 180-190 deg temp taken at the back of the waterpump housing
(where the
probe is on the stock 13b) or after the coolant has passed through the
radiator? And could
somebody refresh me as to ideal and max. temps in both places?
Thanks,
Lonnie

I don't know about ideal but it would be best to take the temperature
of the rotor housing right at the spark plug adjacent to the combustion
chamber and keep that temperature less
than 400 degrees or so. That is the bottom line regardless of what the
water temp is. If necessary drill a small hole and bond in a
thermocouple with JB weld. A 1/16 inch diameter hole 1.3 inches
deep right along side and inline with the leading plug would be perfect.
Best to do this when the rotor housing is separated from the engine.

You can use a Super Omegaclad type J thermocouple page A87
in the Omega catalog #Vol.29 1(800) 872 9436. http://www.omega.com

Either 48 inches or 72 inches long and from .005 to .0032 inch
in diameter. Teflon or glass braid insulation.
I would immerse the thermocouple in JB weld and let that cure first
to be sure it was insulated from the aluminum housing.
JB weld claims to be good to 600 degrees F. You can also
get 1/16 inch diameter ceramic, teflon or fiberglass insulators
from omega. The teflon is rated to 450 degrees F. Glass braid
is good to 900 degrees F.

The under-the-spark-plug type washer thermocouples will not fit the
rotary.

Analog read out meters are simple, reliable and relatively cheap at $112
each.
3.5 inch square. No electrical juice is required. That is what came
with my Cessna.

Basically what you wind up with here is a CHT gauge.

Paul Lamar


lonwood wrote:

Thanks for your answer Paul. I think this is form of CHT is needed to
determine
what the best operating temperature should be.  Like you said this would
best be done
with the engine apart. But for now when people are reporting
that their engines are running too hot, what are those temperatures and
where are they
measured? When I do some ground runs I want to know what to look for so I
don't
overheat.
Lonnie

The water temp probe on  my 1988 is on the back side of the  coolant pump 
at the outlet end of the engine. Assuming your pressure cap is functioning 
and you are near sea level anything over 220 degrees F should be cause for 
alarm IMHO. Without the pressure cap of course the boiling temp of water 
alone is 212 F. I don't know what it is going into the engine.

A fifty fifty mix of water antifreeze boils at 228 degrees F
but the metal temperature adjacent to the combustion chamber according to 
Heinz Heisler book Advanced Engine Tech surprisingly could be as much as 
100 degrees F hotter using 50-50 than when using pure water. This is a lot 
when talking about aluminum rotor housings or cylinder heads for that matter. 
It can also increase the onset of detonation when turbo charging.

In our case I would use  distilled water if the engine is stored inside and 
freezing is not a problem as the specific heat of pure water is much better
than 50-50 water antifreeze. This requires a slightly larger rad but so be it.

If you are worried about corrosion and water pump lube keep the
antifreeze mix down to a minimum.

BTW Heinz also mentions that increased water velocity can improve
heat transfer between metal and coolant where convection is the
main means of heat transfer. Where nucleate boiling is the means
it cannot hurt. This is where the better pump comes into play.
I think Jeff Spitzer, Jim Mederer (Racing Beat) and I agree on 
this point.
 
IMHO that coolant temp sensor is in the wrong place. The hot part 
of the engine down by the spark plugs would be a much better place. Who 
knows what the temp is down there.

As I recall flying with Tracy his coolant temp varies widely depending on
climb or cruise. He does not use a thermostat. Nothing wrong with that
as his bypass is blocked off. His coolant temp goes below 180 at moderate 
cruise and rises quite a bit during climb but we never got above 1000 
feet AGL in the short flight so I don't know what the temperature of 
his coolant would be as a function of his climb profile and percentage
of full power. Do you have that data Tracy? Also I don't know what mix 
of antifreeze he is using.

Paul Lamar
 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org