Subject: 86 RX7 running and oil cooler/ radiator sizing
From: Paul
Date: 6/29/2000, 9:23 AM


I looked at George Grahams installation a week ago, he had a very clean
thermostat housing that I will also try to replicate.  Also some
interesting
comments about how it is required to circulate coolant from the heater
output fittings to get proper cooling.  He got that info from some racers.
I don't know if you end up with some dead ended passages by blocking that
fitting or what.  Anyway, his circuit is to run one cooler on the heater
loop, and a second cooler on the thermostat loop.  The bypass is always
blocked.  He claims the cooling settled right down with that system.

Mike Wills wrote:

OK, so now I have to figure out where the heater plumbing goes. Is that the
hose barb that comes out of the rear end housing below the oil filter pad?

Yes. PL

Never paid any attention to where the heater was connected in the car. Is
there a diagram somewhere that shows the way the coolant flows through the
engine? Seems like a good place to add some additional cooling capacity if
you goofed on your initial estimate for radiator size also. Thanks to both
you and George for the heads up.

As far as Oil cooling, I think he is using a Setrab 625 cooler (2x7.5x13).
My inclination is to use a Setrab 634-10 (2x10.25x13) with the AN10
fittings
from Mazdatrix.  Radiators look like a pair of 1.5 x 10.25 x 13 exchangers


The oil cooler sounds good to me. Im installing a Setrab 925-10. Note that
the dimensions you have here are overall dimensions, not core dimensions.
The core for your 634 is actually more like 2X10.25X10.5 (I dont have the
data sheet here but my recall is you have to subtract out about 2.5 inches
in width from the overall for the core dimension). Total core volume for
the stock Mazda cooler is 180 cubic inches roughly so you should be OK.
Seems George's oil cooler would be a little undersize but its clearly
working for him so he must have the airflow pretty well dialed in. Thats
good to know. Another plug for TMR where I bought my Setrab. Very
knowledgeable and good guys to work with and got my cooler for $145 - $40
cheaper than its listed for on the Baker Precision website.

  I'll be interested to hear how the rad sizing works out for you. I have a
single rad 2X14X20 for a total of 560 cubic inches and Im a little
concerned that it may be a little small. Your core volume is about 400
cubic inches. Keep us posted.
  In hindsight I would have bought a larger radiator, but when I ordered it
I didnt think I had the room. My config has changed about 3 times since I
ordered the radiator and its now clear that I could have fit a little more
radiator in there. If I have any problems I'll consider adding a small
motorcycle rad in the heater loop as pointed out above.

Mike Wills

This is an old schematic but it is simple and clear. This is what I would do in 
your case Mike. Add a hose from the heater outlet back to the input to
the rad. Since the restriction in the return side of the water pump was 
probably put there to enhance the water flow through the heater, re-routing 
the heater flow back to the input to the  rad should enhance the flow through 
the engine slightly without modifying the pump or adding another cooling core. 
Since you have plenty of space above the engine in your RV4 so you do not need a 
modified, low height, low restriction water pump. The higher temp of the 
water out of the back of the block should slightly improve the eff. of the rad
and slightly reduce the overall temp of the engine. The down side is
of course slightly more banana.

Mike, why don't you fly up with Dave to Santa Paula on the Fourth.
I am sure he would not mind sharing the cost of gas :-)

Paul Lamar
 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org

cooling-system-skematic.gif