Subject: Electronic injector failure modes was Re: Digital Fuel Flow System - GRT
From: Paul
Date: 7/2/2000, 1:05 PM

Dave Leonard, make sure you read this about your broken rear housing boss.

Big Snip

 Most manufacturers supply power (+) to the injectors through the
ignition circuit.
The computer controls the injectors by completing the ground side of the
circuit.
This design prevents a shorted injector from destroying the computer. A
shorted
wire between the injector and the computer (ground side) will cause the
injector to
stay open 100% of the time. At low power settings, this would cause the
mixture in
that rotor chamber to go very rich. At cruise power, the rotor would
still produce
good power (albeit a bit rich).

 A short in the power supply (+) side of the circuit would blow the fuse
supplying
power to all the injectors. This would be a bad thing, as it would
affect all the
injectors. On most autos, 1 fuse supplies power to all the injectors.

 Perhaps it would be wise to use separate power supply wires to the
injectors of
the 2 rotors. This way, even a short in the injector or it's positive
supply wire
would only affect 1 rotor (or 1 injector of both rotors). This would
mean you could
still produce 50% power, rather than losing all power due to lack of
fuel supplied
to both rotors. I believe Tracy has taken this into consideration on his
system. If
I remember correctly, his computer design  completes the circuit to the
primary
injector of rotor #1 and the secondary injector of rotor #2 on one
circuit. The
secondary injector of rotor #1 and the primary injector of rotor #2 are
supplied on
the second circuit.

 Question for Tracy    Is my statement above correct? Does it apply to
only the
ground (between injector and computer) side of the circuit? Would you
suggest 2
discrete power supply circuits on separate fuses? It seems to me that
supplying
power to the injectors as I have described regarding the ground side
would make for
a safer system.

Charlie Kuss
RV-8 priming 1 piece main wing skins
Boca Raton, Fl.

Yes, your description is pretty accurate.  I use peak and hold injectors
(most RX7s used these) which require 5 ohm resistors in series with them on
my controller.  The resistor is between 12V and the injector and will act as
a current limiter (or fuse) in the event of a short.  The injector bank
disable switches (used in injector failure mode) feed the primary &
secondary banks separately.

I agree with others who have said that injector failure is very rare (but
not unknown).  Never had occasion to use injector backup mode other than
just testing it, but I like knowing that I have "Plan B" if I should have a
problem.  I can't describe the feeling I had back when I was flying with
carburetors and one of them overheated killing the engine.  Shutting off
fuel too it, closing its (separate) throttle and re-starting on the other
two hooked me on redundant systems forever.

I inadvertantly dumped the message about the broken boss on the end housing
but here is my 2 cents worth.   The missing boss is not one of the critical
ones (the two 'paired' ones but you should have some support in that
quadrant.  If it were me in that situation, I would make a new support by
using one of the perpendicular bolt holes near the top of the engine which
is used to fasten a small sheet metal cover to the engine (not used in
aircraft applications).   You will need to make a simple bracket to do this
but it shouldnt be very hard to do.  Of course it depends on how important
the $300 dollars it would take to replace the end housing is to you.

Tracy Crook
rws@altavista.net
www.rotaryaviation.com


 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org