tommayer wrote:
Paul,
Don't bother with this if you're real busy or it does not have anything
to do with rotaries.
No scanner. I can mail you pics of ramps, if you want to send me snail
address. They're idiot simple. Pieces of aluminum, curved at top to 1 inch
radius, that slide up or down on hardware store screen tracks in the
intakes.
The intakes are standard rectangular affairs. With the doors down the
intakes look just like any RV or Mustang. The doors slide up from the
bottom. With doors up the intakes look like any RV or Mustang with very
small inlets.
With the doors open the intakes measure 70 square inches--that figure
arrived at from an ancient Tony Bingelis Sport Aviation article saying you
needed .35 sq inches per hp for cooling at max power. Experience with high
power hot weather climbs suggests he was right.
With doors closed the inlet area is about 30 square inches.
I don't know anything about drag vectors within cowlings. If this is a
subject that pertains to cooling rotaries and you care to expend the
effort, please explain.
The Mustang has a sloping tunnel arrangement in the bottom of the
fuselage for cooling exit. My exit side cowl flap that did not work simply
pulled up flush with the bottom of the cowl and extended into the tunnel,
when the flap was in closed position, so as to allow only about 40 square
inches of exit.
Kent Paser and other Mustang go fast types have used very similar
arrangments, the difference being that I needed slightly bigger inlets and
greater articulation of the flap because the turbocharger allowed the use of
high horsepower in hot weather at altitude and I had the shock cooling worry
in the opposite condition.
Johnny Thompson, who built a modified retract Mustang with a turbocharged
350 Hp Navajo engine, let the hot air out via tunnels in the sides of the
fuselage, with exit flaps, and closing them increased his speed, with small
but perceptible pitch changes, in case that has significance to this
subject.
All I did when I installed the inlet doors was saw off some of the tail
of the exit flap and glass the flap in place, flush with the bottom of the
cowl. I understood you were supposed to have 120 % of the inlet area at the
exit--84 square inches--and I left about 80 inches. That seems to be
enough.
Closing the inlet doors gives the same sort of speed increase you get
by closing the cowl flaps on a C-180--nearly undocumentable, but it makes
you feel faster. The shutters on Yak 50s and 52s achieve about the same
thing. My doors do allow precise control of engine temps, with NO effect on
trim when you operate them.
Every time I look at your under engine radiator arrangement, I say to
myself, this guy is really smart, all those wonderful race cars, his walls
sagging with all those trophies and engineering degrees, but what he's
drawing here sure looks like what I tried vis a vis cowl flaps with a
radiator in place of cylinder cooling fins. That made me go slower. If he
has not proved his arrangement works in flight, if and when I go Wankel on
my airplane I think I'll stick the radiators behind the baggage compartment
in his W arrangement, do adjustable NACA scoops on the fuselage sides and
maybe the belly for inlets, and let the heated air out the sides or top of
the fuselage, all with due homage to his research on optimum duct shapes.
I remember Tracy writing somewhere about climbing hard with a NA engine
at 10K msl and getting overheated coolant smell in the cockpit, so I think
one of these things with a blower pulling 150 Hp, or 75 %, climbing at 15K
msl at near Vy on a hot day, OAT say plus 5 C (a condition I saw this
morning) is going to need BIG cooling inlets with appropriately bigger
outlets, and coming down hill from FL 240 with the OAT at minus 50 C, in
turbulence so you have to throttle way back or lose the wings, you're going
to need either a vernatherm or an air shut off that really works or what
you'll have out front is a popsicle. You definitely want to avoid slowing
yourself down when you shut the door in cruise.
Again, my technical ignorance is virtually total. Thanks for your
patience. Tom Mayer
The Aircraft Rotary Engine Newsletter. Powered by Linux.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org