Subject: '86 RX-7 ECU Sensors and Codes
From: Paul
Date: 8/21/2000, 6:01 PM

Perry Mick wrote:

Here is some data from my Operator's Manual about the Mazda ECU,
the required sensors, and the fault codes if the sensors fail.

ECU Monitor

The ECU Monitor has two indicators LEDs that monitor the DCC1 and DCC2
outputs of the ECU.  When power is first applied to the ECU, the two
LED's will go on for about 3 seconds and then will go off.  If there are
no more LED flashes, this indicates that there are no immediate
failures.

The codes are displayed with a flashing code. There are short (1/2
second) flashes of light which correspond to a count of 1 and long (2
seconds) flashes which correspond to a 5.  These pulses are counted
until the long pause (2 seconds) that indicates the end of the code.

DCC1 indicates the one's digit of the error code and DCC2 indicates the
ten's digit.  DCC1 will flash either short or long pulses.  Because of
the limited number of two-digit codes (12 and 15) DCC2 will only
indicate a short pulse which counts as 10.  There is a long pause after
which time the code will be redisplayed.

A code displayed doesn't necessarily mean that the sensor described is
faulty.  It could also be caused by a bad connector, loose wiring or a
defective ECU.  The possible error codes are summarized in the list
below. 'S' indicates a short pulse (about 1/2 sec), 'L' indicates a long
pulse (about 1 sec), 'P' indicates the pause (about 2 sec) between the
cycles, and '...' indicates repetition.



     Code 01 - Crank angle sensor
            DCC1: S P .... (1 short light... long pause ... repeat),
            DCC2: does not light.
            Fail-safe mode: There is no fail-safe mode for this sensor.

     Code 02 - Air flow meter.
            DCC1: SS P ... (2 short lights... long pause ... repeat)
            DCC2: does not light
            Fail-safe mode: Maintains basic signal at preset level.

     Code 03 - Water thermo sensor.
            DCC1: SSS P .... (3 short lights... long pause ... repeat)
            DCC2: does not light
            Fail-safe mode: Maintains a constant 80 degree C command.
            Comments: this is the two-wire sensor on the back of the
water pump

     Code 04 - Intake air temp sensor.
            DCC1: SSSS P .... (4 short lights... long pause ... repeat)
            DCC2: does not light
            Fail-safe mode: Maintains constant 20 degree C command.
            Comments: This sensor is built into the air flow meter.

     Code 05 - Oxygen (O2) sensor.
            DCC1: L P.... (1 long light... long pause ... repeat)
            DCC2: does not light
            Fail-safe mode: The ECU stops feedback correction (open loop
operation)
            Comments: This sensor is located on the exhaust manifold.

     Code 06 - Throttle sensor.
            DCC1: LS P ... (1 long light ... 1 short light ... long
pause ... repeat)
            DCC2: does not light
            Fail-safe mode: The ECU assumes 100% throttle position.

     Code 07 - Manifold Pressure sensor.
            DCC1: LSS P ... (1 long light ... 2 short lights ... long
pause ... repeat)
            DCC2: does not light
            Fail-safe mode: Maintains constant command: 96 mm Hg (boost
sensor), 26.3 kPa       (pressure sensor)
            Comments: This is located on the right side wing root area.

     Code 09 - Atmospheric Pressure sensor.
            DCC1: LSSSS P ... (1 long light ... 4 short lights ... long
pause ... repeat)
            DCC2: does not light
            Fail-safe mode: Maintains constant sea-level command (boost
sensor)
            Comments: This is located next to the ECU.

     Code 12 - Trailing side coil failure.
            DCC1: SS P ... (2 short lights ... long pause ... repeat)
            DCC2: S P ...   (1 short light ... long pause ... repeat)
            Fail-safe mode: Stops operation of trailing side ignition
            Comments: indicates a failure within the trailing side
ignition system.

     Code 15 - Intake air temperature sensor.
            DCC1: L P ... (1 long light ... long pause ... repeat)
            DCC2: S P ... (1 short light ... long pause ... repeat)
            Fail-safe mode: Maintains constant 20C (68F) command.
            Comments: This is located on the intake air pipe just prior
to the throttle body.

Note:  From observations, it seems that if more than one error code
exists, the ECU reports only the one of lower numeric value.

--
Perry J. Mick
Duckt N7XR
http://www.ductedfan.com

 
The Aircraft Rotary Engine Newsletter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org