^ >> ^ >>>> FlyRotary <<<< ^ << ^ <<<
! >> ! >>>>>>>>>><<<<<<<<< ! << ! <<<
Subject: Another of my 13B photos, and 'HOLY COW' - take it easy on me!!
Date: Sat, 26 Feb 2000 11:08:57 -0800
From: Andrew Venable <avenable@uswest.net>
To: plugsup@olsusa.com
Andrew Venable wrote:
Ok everybody, I just got back into town and am
amazed at the controversy created by sending my
one photo out over the net. It is not my
intention to promote any form of 13B
installation. I thought ( after much prodding )
that viewing my 13B installation would aid in
others making the journey. I was advised by the
Ross Aero people early on ( back in 1989) to mount
my engine "plugs up". This was because I used a
MA4-5 updraft carburetor ( off a O-360) and plugs
up would make the intake manifold easier. Also at
that time I was using a stock 1985 Mazda
distributor, which would have poked up through the
cowl if the engine was not rotated. I also wanted
to use the stock Mazda exhaust manifold with a
single pipe attached, and rotating the engine
aided in this installation. My plane has plenty
of room below the engine, so mounting the
radiators below was no problem. I did investigate
the oil return problems with the engine rotated,
and concluded that oil return would be
sufficient. Granted rotating the engine placed
the oil return holes for the front/rear bearings
on the side. After considerable conversations
with the Ross people, it was determined that
having the main bearings half filled with oil
before returning to the tank was not detrimental.
One advantage is that at cold starts the main
bearings are half filled with oil ( pre-lubed ).
As such I plowed through the installation, working
through all the head-aches encountered. First
flight was 17 September 1994. After about 35
hours of flight time using stock pulleys and one
belt to drive the alt and water pump, I decided to
have somebody look at the engine as a preventative
maintenance and to install dual pulleys sized for
high rpm's. I chose Atkins Aviation, who
performed a total tear-down, installed new
bearing, seals, etc., and pulleys. Not one word
was spoken about heat cracking, or oil
deprivation, or bearing wear problems. In fact
Dave was surprised how clean the inside of my
engine was. Dave did a good job for me. Any way,
I reinstalled the 13B and have been flying it ever
since "plugs up". One correction I should make is
I only have about 400 hours on this installation,
not 750. Give me some more time, and work
permitting I will reach and exceed 750hrs.
Well, with enough rambling ( disclaimer ) here is
another photo. I apologize for the size of these
photos. I have not figured how to make them
smaller. I am using Adobe Photo Deluxe and
Vista-Scan software. Any suggestions will be
appreciated.
This photo is the left side of the engine. I have
switched ignition systems to Tracy's EIC. It
works nicely. The front scoop of the cowl feeds
blast air directly to the oil, water, and intake
carb filter. There is an aluminum sheet metal
cowl which forces air directly through the water
radiator. Air passing through the oil radiator
flows back through the main engine compartment and
exits out the bottom of the cowl. I do use a cowl
flap on the bottom, which also works nicely. The
two rods which actuate the flap can be seen
dangling under the water radiator. You can see
the black carburetor mounted under a custom intake
manifold. The custom intake manifold is welded
out of .040 4130 sheet and is sort of box shaped
forming a 90 degree turn. It connects to the
stock Mazda intake manifold coming from the bottom
of the engine. I built small water jackets out of
aluminum and glued these to the sides of the box
intake manifold. I take hot water from the engine
heater core outlet ( now on the top of the engine)
and feed through the little water jackets to keep
the 4130 box heated. Doing this did make a small
difference in performance. The water after
flowing through the three water jackets returns to
the main radiator. I use two sears Diehard
batteries in a dual system. I also have a flap
mounted directly behind the oil radiator. You can
see the control cable for this running across the
carburetor. I use this to control the air flow
through the oil radiator when flying on cold
days. My fuel system is gravity feed from two
wing tanks. You can see the gasolator mounted on
the firewall below the water radiator. My engine
came from Japan in a crate. I decided to use the
stock Mazda exhaust manifold ( with it's weight
penality) because of the fancy porting inside the
weldment. You can see it just above the oil
radiator. I will probably work on a lighter
version next winter. This manifold does provide
significant muffling qualities however as I do run
a straight SS pipe directly out the right side of
the cowing..
Well here goes, read - view and weep.
Andy
-------------------------------------------------------------------------------------
[Image]
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org
Homepage: http://www.members.home.net/plugsup/
Subscriptions: http://olsusa.com:100/guest/RemoteListSummary/flyrotary