I am sorry if I seem a bit impatient and frustrated about this subject.
Sometimes I feel like I am knocking my head against the wall.
About Sept. 1998 I tested some tea spoons full of oil in a temperature controlled
industrial oven at 500 degrees F for one hour. I choose 500 degree F because
Mazda says in their SAE technical literature that a well lubed apex seal runs
500 degrees F at WOT at 6000 RPM. See attached files. Part of the reason
for this is the seal opens the exhaust port first and high temp and medium
pressure gases squirt out the port heating the seal in the process. This
is in addition to its normal duties. The new side exhaust port RX8 engine
may help this situation.
Brand new common
motor oil without dirt in it turned pure black scum gunk
in the oven after one hour. Mobil One was better but not as good as two cycle
oil or turbine oil. Marvel Mystery oil also turned to black gunk. I uploaded
the results on here so it is on the CD. However you can perform these test
for yourself in the family oven.
The question of burning came up. I was not able to ignite two cycle oil directly
but Paul Yaw, a race rotary engine builder of good reputations, was able
to get it to burn and leave NO deposits by mixing gasoline 50/50.
It matters not to me if you mix it in the tank or use Richard Sohn's aux tank
adapter and the stock Mazda injecting pump but by all means use two cycle
oil or something equally good to lube the apex seals. Your engine will last
much longer and be more reliable.
Here is the first of two of Paul Yaw's old messages on the subject.
Paul Lamar
_____________________________________________________________________
Paul Yaw wrote:
Paul wrote:
Not much more than I already mentioned. Two cycle oil is the best all
things considered. Turbine oil is risky as it may have an effect on seals
used in the engine.
Here is a jpg of the apex seal temp. apextemp.jpg
You can see how important it is to cool these seals.
You need an oil that will take high temps.
Paul Lamar
Motor oil does not burn cleanly, and has a detrimental effect on the
detonation resistance of the fuel. When I disassemble an engine, I can
tell just by the amount of carbon buildup if an engine has used the
metering pump, or was run on a two stroke premix. Engine oil will leave
a TON of crud behind. In many cases, I have seen engines with no
compression, only to find during disassembly that an apex seal was stuck
in the rotor tip because of carbon buildup. In many cases a high
mileage rotary will start to develop detonation problems because the
carbon buildup retains heat, and ignites the mixture before the flame
front can. Increasing the output of the metering pump only makes things
worse.
Paul Yaw
So, Paul, I guess you recommend two cycle pre-mix. Is that right?
Sounds like it.
PL
_____________________________________________________________________
Another old message from Paul Yaw.
Paul Yaw wrote:
It's not an urban myth, it just depends on the oil. Some of the better
two stroke oils mentioned here previously will do the job without
increasing the likelyhood of detonation.
Paul, what 2 cycle oil do you recommend for turbocharged engines?
Charles Harbert
I don't really have a good answer because I don't know what these oils
are made of, or why. It's all just a bunch of slippery goop. I burned
a bunch of oils once in glass dishes to see how much crud was left
behind. Motor oils made a big mess, cheap two stroke oils were better,
and expensive two stroke oils left very little on the glass. The amount
of visible smoke from the exhaust seemed to correspond with what I saw
in the glass but I didn't try all of them in an engine. I finally just
decided that whatever the two stroke racers say is good, is good. The
oil HAS TO work well in high strung two strokes, so I figure these guys
have a pretty good clue.
If you want to see something you will not believe, buy some Golden
Spectro synthetic, smear some on a piece of shiny aluminum, and light it
on fire. After it is done burning, you will see a thin film of brown
gunk. This gunk is VERY slippery. Now take a torch and heat it up, and
the film will dissapear. No joke, it will just plain dissapear, leaving
you with the same shiny piece of aluminum you started with. A lot of
two stroke racers swear by it and Yamalube R.
Did I spell dissapear right?
PY
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org