Leon Promet wrote:
G'day Paul,
Had a REAL good talk to my Bell housing mate Jeff this afternoon. No
worries! We can make a new set of patterns from the existing ones
pretty
easily. Can do it for either the later model '86 onwards
flywheel/starter
motor combination, or the earlier model. I think there would be more
call
for the later model. I've taken some pix, but won't be able to post
them
for a couple of days.
It is possible to incorporate any provision for any mounting
arrangements
that you like. The mounting pads can be made thicker, strengthening
ribs
can be added to the bell housing as required, and the thickness of the
housing can be varied. I could mimic your plate mounting idea and
integrally cast them with the bell housing itself or they can be cast
separately as custom mounting brackets etc etc. Give me some ideas of
what
you think Paul. I'll be going out to see Jeff again later this week
with
my Subaru sketches once I have my ideas formed up.
Jeff usually uses 6061 for his auto bell housings, and they are
obviously
sand castings. A range of casting alloys is available, and can be
specified in the case of a batch run. It's a bit hard to do this though
when doing one-offs.
Preliminary costings are around $475 ~ $575 AUD ($250 ~ $300 USD ) for
individual units, depending on the bolt pattern drillings on the PSRU
mounting face and complexity of mounting provisions that need to be
incorporated in the patterns etc. This price could be brought down
considerably if 5 or more units were ordered at a time, as a lot of the
cost is in the set-up time. I'm also currently costing having them
X-rayed
for casting flaws. (Not an issue with auto apps, and none have ever
broken in service, but there are a different set of loads applied in
an
aero installation and I don't want to take any chances in the air).
My suggestion is that I supply the bell housing unit bored, drilled and
tapped to take a Mazda Starter, but leave the PSRU mounting face itself
flat with either a pilot hole or a machined register that gives the
centre
of the mounting face. People can then get their own engineer to adapt
any
PSRU they like.
If I have the correct bolt pattern drawing for the PSRU, it can be
drilled
at the time of supply. Obviously, it is cheaper to do it all at the
same
time and in a batch, and as the numbers go up, the cost comes down.
Current timeframe to produce a prototype would be 3~4 weeks, and once
the
design is settled, they would be available to order 2 ~ 3 weeks after
that.
I'm also looking at producing billet H/T alloy flywheel/drive plates
which
will take a standard Mazda ring gear. I need to look at the long term
sales potential, as these could be churned out on a CNC machine quite
cheaply. We need to also think about vibration isolation dampers as
well,
as this will dictate what the driveplate looks like. I'm also in the
process of hunting down a sustainable supply of starter motors.
I propose to be able to supply a complete package which will include
bell
housing, drive plate, vibration isolator, ring gear, starter motor
plus
all the necessary nuts, bolts etc to do the job. All bolts will be
plated
Metric H/T grade 8.8 unless you require something tougher. It is
entirely
possible to use H/T aircraft bolts, but unless the threads in the
motor's
end housing are helicoiled to take the same aircraft quality bolts, it
would be overkill. Let me know if you are interested.
Cheers mate,
Leon Promet
We will put our heads together when I get down there Leon. I am working
that out with my wife as we speak.
BTW is 29 inches center to center on the rubber bushings OK with most of
you guys
building a side by side type airplanes? This will accommodate a stock
turbo, custom
turbo or tangential muffler in the cowl. You RV4 guys will be on your
own. The tandem RV8 uses the wide cowling. We will make the PSRU mounting
surface flat
with no holes so Tracy can bolt up his PSRU and make any changes he wishes
except for the 3.550 distance from the back of the engine to the PSRU
mounting
plane.
How does this sound guys? Tracy? Let me know with comments before we make
the patterns
for the castings.
Sounds good to me. This eliminates any concerns over lateral stress for the
engine mount/redrive adapter. Keep in mind that nothing fits together
without design work. The adapter thickness needs to be matched to the input
shaft length, the damper (if Leon ends up making these) needs to be matched
to the input shaft spline, etc, etc. Leon, will the auto trans flexplate
(that I use) fit in the proposed bellhousing? It is slightly larger in
diameter that the manual stick trans flywheel. If Leon makes the flywheel
this would be a non-issue.
Tracy Crook
tcrook@rotaryaviation.com
www.rotaryaviation.com
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org