http://www.rotorsportsracing.com/new333.html
Located between Kannapolis and Mooresville, NC approximately 25 miles North
of Charlotte, NC.
RotorSports Racing
465 Russell Farm Road
Kannapolis, NC 28081
Phone: (704) 933-6222
Fax: (704) 933-5906
info@rotorsportsracing.com
Stages and Re-build Prices:-
Stage 1
Stock Rebuilds are an economical choice for engine replacement without
sacrificing reliability. Each engine receives careful inspection upon
disassembly and all components cleaned and checked for wear or damage. All
engine seals, bearings , gaskets and related springs and rubber "O" rings
are replaced with new OEM parts. The side housings are micro-lapped to
restore them to better than new condition. Engine Rotors, and Rotor Housings
are reused only if in excellent condition and chosen by the customer over
new ones. Engine assembly includes installation of front cover and sealing
the oilpan, additional accessories can be installed as well at customers
request. Stage1 StreetPorted Engines are prepared the same as a Stock
rebuild but feature porting of the intake and exhaust ports to maximize
engine power without adversly affecting street driveability. Porting can
only be performed on excellent condition used or new housings and may
require additional component replacement.
Stage 2
Engines feature new rotor housings, upgraded apex seals with heavy duty
springs, competition oil seal springs, new oil pump and chain, high pressure
oil regulator, and improved design high flow main bearings.
Stage 3
Engines include all of the Stage 2 preparation plus the engine rotors are
machined and heavy duty 3mm apex seals with dual springs are installed to
prevent seal "skipping" at high rpms and reduce the risk of engine damage
>from high turbo boost. Additionally the Rotors are race clearanced, Rotor
Housings are modified for improved cooling, the oil passages are enlarged,
and Eccentric Shaft modifications are performed.
Stage 4
Engines are built using all new engine components modified to racing
specifications. All Stage 3 preparation plus careful selection of both
competition and modified OEM parts to build the best motor for your needs.
Recommended for highly modified normally aspirated and turbo/ nitrous
engines.
Bridgeported Race Engines Available in Stage 2, 3 or 4 preparation levels.
Custom ported intake and exhaust for your intended racing application.
Type Stage 1 Stage 2 Stage 3 Stage 4
12A $1499.00 $2299.00 $2599.00 Call
13B $1699.00 $2549.00 $3399.00 Call
'85 and earlier
13B $1799.00 $2799.00 $3499.00 Call
Non Turbo
13B $1899.00 $2899.00 $3499.00 Call
Turbo
13B $2199.00 $3199.00 $3699.00 Call
Twin Turbo
StreetPorting- add $350 per engine
Bridgeporting- From $550.00 per engine
Prices based upon customer supplied engine core in rebuildable condition.
Additional core charge if no core provided.
ENGINE REBUILD KITS
We have assembled engine rebuild kits for customers who wish to rebuild
their own engines. All kits come complete with your choice of Apex Seals,
Corner Seals, Side Seals, Oil Seals & O-rings, and all associated springs.
To compete your assembly a complete Engine Gasket Set, Front & Rear Main
Seals, Pilot Bearing & Seal are also included.
Please note that Rotor & Main Bearings must be ordered separately.
The following is a list of other engine modification services that we offer
Street
Porting
Bridge Porting
Rotor Maching (3mm / 3.5mm Seals)
Modify Rotor Housing (Water Jacket)
Eccentric Shaft Modification
Lapping
Ultra Sonic Cleaning
Powder Coating (20 different colors available)
Refer to catalogfor Pricing
marc wiese wrote:
They also can get factory rebuilds (facility in Jacksonville, FL) at real
good prices.....
That is what they did for me.
Marc Wiese
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org