Subject: Extensive differences text in engines from year to year.....
From: Paul
Date: 3/19/2001, 5:47 PM

marc wiese wrote:

Subject: Re: (rx7) [2] 13BT --> 13B-REW swap for Turbo II
13BT vs. 13B-REW: (Last revised Aug. 14, 1997)

There are two types of 13BT blocks, one from the 87-88 Turbo RX7 (FC3S
GTR) and one from the 89-91 Turbo RX7 (FC3S GTX). While the older 13BT
GTR block differs a lot from the 13B-REW block, the GTX block is some
what a compromise in between. Most of the changes made by Mazda
engineers are refinements to address the problem areas of the previous
designs. For comparision purposes, the 13B-REW motor described in this
article is the one from the FD3S, not one from the Japan-only Mazda
Cosmo.

One significant difference on the 13B-REW is the areas around the dowel
pins on the side housings. They are reinforced and ribbed with thicker
castings. This is a major problem area on high output 13BT engines, as
they tend to crack at high power levels and is the main reason that the
13BT blocks are not reliable beyond 400HP. Most competent rotary
rebuilders will look for this before rebuilding a 13BT motor. The 13BT
GTX blocks are said to be more reinforced than the earlier motors but
not as significantly as the newer 13B-REW designs. Before the
introduction of the 13B-REW motors, some engine builders experimented
with brazing extra metal around the dowel pins area on the side housings
of the 13BT motors.

The port sizes on the 13B-REW are extremely larger than the 13BT's,
especially the primary ports on the intermediate housings. This is
accomplished by increasing the height of the side and intermediate
housing where the ports are located and relocating some of the coolant
passages inside the housings. The larger ports increase the duration and
"lift" of the intake stroke, allowing more air to be ingested into the
combustion chamber. While the intake ports are larger, the intake
runners of these motors are still about the same size. The 13BT intake
manifold has a surge tank plenum which is found to create too much
pumping losses because of its large volume. The 13B-REW intake manifold
is a "Dynamic Pressure Intake System" which eliminated the surge plenum
tank and has opposed-facing secondary intake runners. This new design
enhances intake flow by taking advantage of the strong pressure waves
inherant in rotary engines. The throttle bodies on the 13BT are 3x45mm,
while the 13B-REW are 1x45mm + 2x50mm.

* Intake Runners: Upper, Lower
* Plenum: 1, 2
* Runners: 1, 2

Contrary to popular beliefs, the 13BT's and 13B-REW share many internal
components. The 13B-REW rotors are interchangable with the 13BT GTX
rotors, although they don't have the same part number and thus are not
the same part. But they do have the same compression ratios of 9.0:1 and
they weigh the same. The CR of the 13BT GTR rotors are 8.5:1. I believe
the later model rotors are manufactured from a more accurate milling
technique while the older ones are left partly casted. This is evident
in the bathtub faces of the rotors.

Almost all the internal seals and springs are the same parts in the 13BT
and 13B-REW. This includes the 3-piece cast-iron 2mm apex seals which
are found on all post '86 rotary motors, both turbo and non-turbo. With
the exception of the side seals and corner seal springs, all the other
rotor parts of the two motors such as oil seals, rings, springs, side
seal springs, and corner seals, are the same parts. The newer design
corner seal springs are reccommended for use in all rotary rebuilds.

The eccentric shafts for these motor seem to all look the same, but the
13B-REW shaft has a larger oil bypass/crank pulley bolt. The newer motor
surprisingly maintains the same warm-up oil-bypass pellet as the older
motors. The 13B-REW motors does have larger front-end thrust bearings
than the 13BT motors. These larger bearing components require the use of
a different front counterweight. The larger thrust bearings allow better
loading and thus a tighter torque setting of the pulley bolt. This
design will reduce the chance of the eccentric shaft bending at the
front section, which is sometimes a problem on high-output 13BT motors.
The large thrust bearing is probably also designed for use with the pull
type clutch assemblies found in the FD3S.

The front cover of the 13B-REW has one more attachment bolt which
prevents the gasket from blowing out, which is a problem on the 13BT
motors. These front covers are interchangable between the two motors as
the bolt patterns are the same (except for the one extra bolt on the
13B-REW). The 13B-REW motors uses crank trigger sensors mounted on the
crank instead of the crank angle sensor (CAS) on the 13BT. The crank
trigger sensors allows a better accuracy resolution because of its wider
teeth spacing. Also, torsional flex on the crank angle sensor shaft
causes inaccurate readings. The two triggering systems has similarities
in the numbers of triggering teeth. The 13B-REW's crank trigger has 12
syncro teeth and 1 home tooth, while the 13BT's CAS which spins at half
speed, has 24 syncro teeths and 2 home teeth.

The rotor housings on the 13B-REW motors are refined for reliability.
Since the motor is designed for higher standard output, the wear surface
on these housings has a carbon-graphite coating which is said to exhibit
32% less friction than the 13BT motor's fluorocarbon resin coating. The
new coating actually allows less oil to be injected into the combustion
chambers, thus the 13B-REW requires only two oil injectors instead of
four. In addition to this coating, these rotor housings has the water
passage machined around the spark plug areas to increase cooling at the
spark plug tips. This modification is similar to the ones done on race
motors.

The stationary gears on the 13B-REW are factory hardened. They are
interchangable with the 13BT's, provided that the 13B-REW's thrust
bearings and front counter weight be used. Inside the stationary gears,
the standard main bearings on the 13B-REW motors are the multi-holes
type and are locked into place by an anti-rotation set screw. This
design, similar to the "3 window-type" bearing is pioneered in the
earlier LeMans and IMSA motors. The holes allow extra oil to flow around
the oil groove thus providing a thicker oil film for the eccentric shaft
to ride on. The 13BT has standard bearings with no oil holes. Oil pump
capacity and pressure are also increased in the 13B-REW motors. The oil
pumps are not interchangable. The 13B-REW oil pressure regulator is
interchangable with the 13BT motors and is a reccommended upgrade when
power output is increased. Also, a new oil pan design on the 13B-REW
motors helps to minimize air induction into the oil strainger. A thinner
pan with a inner bulge maintains oil level to keep the oil strainer
submerged in oil. The 13BT GTR blocks use mechanical oil metering pumps,
while the 13BT GTX and 13B-REW blocks use electronic oil metering pumps.

The water pump of the 13B-REW is probably the only reverse rotation
water pump assembly found on any Mazda rotary engine. It is driven by
the back of the serpentine belt. The water pump housing assembly on all
the rotary engines are interchangable, but the appropriate front
cover/pulleys/etc... must be used.

Fuel injectors used in the 13BT motors are 4 standard Nippondenso top
feed rail injectors rated at 550cc. Depending on production dates, the
13BT motors had both low and high impendance ratings. The 13B-REW motors
has 2x550cc injectors for primary and 2x850cc injectors for secondaries.
This higher fuel capacity is for higher power levels. These injectors
are side-feed rail types with high impedance so it can operate cooler.
They are not interchangable with the 13BT injectors.

The engine mounts locations of the 13B-REW are under the rear side
housing, while the mounts on the 13BT are located on the intermediate
housing. Because of this, interchanging the motors between the FC3S and
FD3S chassis is a very involved project.

The tranny bellhousing bolt patterns are the same on the 13B-REW and
13BT motors, thus the trannies are interchangable with the appropriate
clutch/flywheel assemblies.

In summary, because of these and many other refinements, the 13B-REW is
a much more potent powerplant which can easily handle high HP output
beyond for which it is originally designed for. Many of these
refinements are shared in the designs of the 20B-REW and 13B-REW of the
Mazda Cosmo.
Any questions or comments? Please send email to pko@mindspring.com

Reference
* S. Tashima et al, "Sequential Twin Turbocharged Rotary Engine of the
Latest RX-7", SAE paper 941030

The AirCraft Rotary Engine NewsLetter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org