Subject: Design & Weight of Bell Housing dimensions
From: Paul
Date: 3/20/2001, 6:48 PM


The problem with this layout is it won't work with a turbo.
The turbo will heat the back side of the left rad. With one rad on the
bottom and a left side exhaust both turbo and tangential mufflers are
easily accommodated on the left side of the up right engine in the
cowling.
Also one rad will be more efficient than two rads in series as  shown
here.
Simplicity is a virtue.

I won't go into the myriad cooling and oil system drawbacks of the plugs
up
engine shown in this picture again unless I am forced to. If God and the
Mazda
engineers wanted to mount it that way they would have done it in the RX7.

We have been all over this in the past many times in the past.

Paul Lamar


No need to Paul, I believe we all have a fair understanding of your views
concerning Plugs UP {:>).

Actually, I have test fitted the 91 turbo charger just out of curiosity.
With a little grinding on the turbo exhaust manifold it can be bolted to the
block  in a reverse of its normal orientation.  It, of course, hangs below
the block in my configuration and neither of the coolant radiators are in
unobstructed line of sight and would not be a problem with radiant heat.
The oil cooler on the other hand, being on the bottom and approx 13" away,
would require some shielding.

 A bigger drawback, in my view,  is that if I ever decided to use a turbo, I
would have to have a scavenger pump to pump the oil back to the pan (similar
to what Chuck Harbert used for his gearbox).  That is one reason I was
interested in the Aerocharger turbocharger which has its own self contained
lubrication system.  But, apparently that turbo in its current configuration
is not up to sustained punishment of the rotary exhaust. So it is likely I
will stay naturally aspired - well, perhaps if I got really bored {:>).

Speaking of power, with Tracy's and Finns assistance (I stood out of the
way, while they worked), they corrected the flaws in my wiring of the fuel
flow meter (Tracy's design) and I got it hooked up .  I warmed up the engine
and went to WOT which gave me 5800 rpm, the fuel flow meter read 14.5 GPH.
I made no attempt to refine any settings on this first test.  But, the 14.5
GPH came out to around 155 HP static at 5800 rpm, corrected for density
altitude.  Doing some calculations, this rpm and fuel flow indicates I had
an air/fuel ratio of 13.25:1 at that rpm.  If that is correct, then bringing
the AF ratio to 12.65 (Best Power) would increase the HP to 163 HP at 5800.
This indicates that 6150 rpm should be knocking on the door of 170 HP or
better.  Soooo much better than what I was getting out of the older engine.

 Now, with  the fuel flow  meter, I can immediately tell whether a change
increases or decreases HP(i.e. fuel flow).  I intend to vary the length of
my adjustable length intake manifold (can adjust it a total of 5", 3" with
the cowl on) and see if it makes any difference as well as work with the
air/fuel mixture ratio and ignition timing.  Even if the meter is not
precisely calibrated to give actual real fuel flow (actually it appears to
that pretty well, probably depends on how much effort you want to put in
calibrating it), it will give relative increase or decrease so will take
more of the guess work out of tuning.

Finished drilling two 48" long, 2" dia 0.035 SS tubing full of 1/8" dia
holes for the next try at the holey muffler.  I intend to hang them this
week and fly it Saturday and see if I can hear myself think in the cockpit.
Trying to get it fixed so I won't be banned from Sun & Fun.  I trust you are
still planning on attending.

Will report on results.

Best Regards

Ed

Yep I'll be there Ed. I am bringing the check book from the Everett Hatch Memorial
Fund for any one going 200 MPH in the Sun 100 with a rotary powered airplane. I think 
Tracy has a good chance if he tries.

Paul Lamar

The AirCraft Rotary Engine NewsLetter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org