Leon Promet wrote:
Hi Guys,
To short circuit all this "Pencil Pilot" and "Interplanetary Rocket
Scientist" stuff, all that is needs is for some enterprising dude to get
in a '91 FC or a '94 FD and drive it up over the Rockies. I believe that
there are heaps of places that are up around 10,000 feet. If it works in a
car, maybe it'll work in a plane??
Who's gunna volunteer? I can't help much as I live in the Antipodes and
the biggest lump of rock in OZ is only 7,316 ft AMSL, and most of the
roads around about are 6,000 ~ 6,500 ft, but they work real well there.
I think a nice trip up over the Rockies will put all this to rest real
quick!
I've been told on reliable authority that there are plenty of places over
12,000 ft. Much above that and you will need oxygen anyway.
How high is Pike's Peak? The turbos on the race cars don't seem to have
any problem coping with the altitude differences from bottom to top??
As for a triple rotor, 4~5 PSI @ 5,700 RPM is good for about 290 ~ 300.
If you get real smart and put 9.7:1 rotors in it, you will get nearly 260
neddies @ 5,700 naturally aspirated. A couple of pounds boost will take
you well over 300 BHP.
The higher the compression ratio, the less boost you need for a given
power output. It's all related to BMEP. (Brake Mean effective Pressure).
Before anyone starts to flame me about how you must decompress the rotors
in turbo engines, power output is directly related to BMEP.
You can get an increase in BMEP in one or a combination of several ways.
1. Increase the volumetric efficiency by adding more port overlap, (Close
the inlet and the exhaust ports later and get rid of all the sharp edges),
2, Better induction and exhaust design/tuning. (Correct length inlet and
exhaust runners for the chosen RPM)
3. Up the compression ratio
4. Cool the inlet air (make it more dense)
5. Compress the air with a blower or a turbo and/or ram air. (make it more
dense and then cool it!)
6. Slower burning fuel (higher octane)
7. Careful attention to mixture strength
8. Careful attention to ignition timing
9. Use of water/alcohol augmentation. (suppresses detonation as well!)
Finally, once you have done all you can to increase BMEP, more power can
be had by:
10. Revving the sucker a bit harder! (higher PSRU ratio & bigger
prop/variable pitch).
If you do a little bit of all the above, you end up with a SUBSTANTIAL
increase in horsepower. The higher the compression ratio, the less boost
you need for the same BHP at the same RPM..
You guys also really need to give up on this Inconel wheel business. Fine
if you are going to run up to 2 Bar of boost like Jim Mereder is running in
his 900 BHP triple rotor, but a total waste of time and money and mental
anguish for a mildly tuned aircraft application. A stock Mazda '91 turbo
exhaust wheel starts to degrade over 1750 deg F. Run the thing at 1550 ~
1600 and it will last a LONG time.
Rotaries are also not like piston engines that have melty-melty or
breaky-breaky aluminium pistons, and burny-burny exhaust valves and seats
to worry-worry about.. Rotary pistons are cast iron, and the critical
issue is simply apex seals and detonation. Which sort of brings me to the
next topic.
If you are REALLY worried about exhaust gas temp, or detonation, a little
water/alcohol augmentation will kill a lot of the heat and give more power,
(simply by increasing the BMEP, which is a natural consequence of
increasing the charge density while reducing the flame temp and it's rate
of propagation thus allowing you to run more advance etc).
The only time you will REALLY need water injection is on take-off and climb
out, but it CAN also be definitely beneficial in cruise. Rotaries
respond well to leaning in cruise. All you then need to do is monitor you
exhaust gas temp. Instead of using mixture to control CHT (like you do in a
Lyc), a little water injection will tend to dampen the fire without
decreasing the net power. You don't need a lot of water unless you intend
to fly flat strap ALL the time as in air races.
Have a REALLY CAREFUL read of the following, the NACA paper in particular.
Between them, they have done a pretty good job of explaining it. Water
injection was routinely used on all forced induction aircraft engines in WW
II. It is currently used on lots of racing and rallying turbo cars. The
theory and practice hasn't changed in 60 years!!
http://naca.larc.nasa.gov/reports/1945/naca-wr-e-264/
http://www.aquamist.co.uk/dc/dc.html
http://www.highpower.freeserve.co.uk/water.htm
Hope this has been of some assistance.
Best wishes and kindest regards,
Leon Promet
peon@pacific.net.au
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org