Subject: ND alternator and GAMI injectors
From: Paul
Date: 3/26/2001, 1:25 PM


Leonard Garceau wrote:

Ready to wire up.

Where can I purchase a new ND alternator?  Any suggestions appreciated in
advance.


Paul Lamar replied:

Gee I just had the guy that works on my wife's 83 RX7 put a new alternator on
it. I imagine any auto parts store. Pardon my ignorance but what do you mean
by "ND"?


Speaking of Nippo-Denso ("ND"), I forgot to tell you about the tour of the GAMI
facility in Ada, OK, I went to two weekends ago.

First we started with the design office.  Lots of "ooing" and "ahing" over the
SolidWorks workstations (I'm in computers so this was kinda "so-what" for me.
But then I have a dual Pentium III server as one of my several comps at home).

Then we took a look at their cherry T-34.  Too bad it's hamstrung by the wing
spar issue.  They are working on a "alternative method of compliance" to the
coming AD.  You know, the one with the recurrent wingspar eddy current
inspections ever 100 hrs or so?  Yes, the one that is estimated to cost about
$15K a whack.  OUCH.  Their method involves a one time eddy current inspection,
and strengthening of the wing spar with a convoluted doubler.

Then we viewed the GAMI-jector flow bench.  That is where they very carefully
measure the flow rates of the injectors in order to build up matched sets (BTW,
the test solution reeks to high heaven).

Then off to the "supplenator(tm)" test bench.  This device is very
interesting.  They take a Nippon Denso alternator, crack the case, spline the
shaft, add an in-house designed half case, and an aluminum box full of
electronics.  The result?  An auxilliary alternator that has 3 independent
output buses (main, essential avionics, engine electronics) rated at about 35
amps (don't remember if that was 14V or 28V; it works at either voltage) that
auto-shares the power load with the primary alternator.  They are currently
doing the FAA paperwork for certification.  A pair of these puppies (perhaps
using the unmodified case & shaft) seem like a good basis for an auto
conversion's power system.  See http://www.gami.com (it's funny that the
"picture" with the PRISM text is really the control module for the alternator.

Then we look at their detonation torture engine.  The have been studying the
problem of detonation.  They took a ground power unit engine and plumbed it to
5 fuel cans using a stopcock tree.  The fuels were: 100LL, 82 mogas, Jet A,
80%/20% mogas/naptha (or maybe naptha/mogas), and 100% naptha.  Crank the
engine, run the throttle up, switch to 80/20 and knock-knock-knock...  Switch
on the engine control computer, purr-purr-purr.  Twist stop cocks any way you
want: purr-purr-purr.

It turns out that their engine management computer only has *two* inputs: crank
position and compustion chamber pressure.  They use some kinda patented
opto-electronic direct pressure sensor (reads pressure at the spark plug via a
machined groove along the threads).  The computer advances or retards the spark
as needed to try to keep the maximum chamber pressure peak near the point of
maximum mechanical effenciency (about 18 deg ATDC on their engine) while
monitoring the onset of detonation.  Showed some pretty nifty pressure graphs
that displayed obvious precursors to detonation.  The engine computer samples
the sensor at "30,000 per second" (32KSPS I presume; not an unreasonable
sampling rate).  They are currently working with the FAA on a combined
electronic ignition system using htese sensors.   I wonder if the sensor could
be used on turbo-charged Mazdas?

They had a Superior engine (IO-360) in the test cell undergoing accellerated
testing (running at 200 HP).  Man!  What a setup.  It looked alot like the
consoles you see in the Houston NASA control rooms.  LabView running on about 6
computers, simultaneously collecting great huge gobs of data.  Enough 19"
monitors around the operator to give him/her a good tan at the end of the day.
I think they said you could monitor the test from the web at
http://www.engineteststand.com and (with the correct plug-ins) see the LabView
data.  The picture on the website doesn't do the room justice.  While we were
their, there were extra monitors stacked on top of the console, the cabinet in
the background was open and wires were snaking everywhere.

Then we had lunch.  BBQ.  Yum.

Check out the "Future Series" stuff.  Lots of really interesting info on engine
leaning and balanced fuel injection.  http://www.gami.com

Russell Kent

 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org