Subject: The quest for more HP
From: Paul
Date: 3/26/2001, 12:33 PM


 Chuck,
    My 13B powered RV-6A with the 6 port gave me a top speed of 186
MPH
TAS
(GPS Verified) .  I initially estimated my HP to be in the 160 HP
range.
I
then did a very careful measurement of my fuel burn.  By flying WOT
off
one
tank for 30 minutes using the other tank for take-off and landing.
The
resulting fuel burn was 10.57 gallons/per hour.  I was pretty pleased
with
the great mileage until I realized it was the results of low HP.  This
works
out to approx 114 HP for the rotary at 8000 MSL.  This translates in
to a
sea level HP of approx 152 HP.  This was with the engine in its peak
condition.

Later due to the faulty installation of an apex seal with overtime
caused
sufficient scoring of the side walls to drop performance, the HP had
decreased due to the damage to around 130Hp before I stopped flying it
and
changed engines. By this time the top speed had dropped to the 170 MPH
range.  While in the air it was not that bad, mainly climb was slow
and of
course top speed was down, but it was still 40 mph greater than the
Pipes
and Cessnas I was use to flying..  However, where I really notice the
lack
of HP was take off on hot days on short runways.  Make for Looonggg
take
off
rolls and ROC had fallen to less than 1000 fpm.

If you really want to get a fairly accurate measure of your HP.  Do a
carefully controlled timed fuel burn at WOT at 7500-8000 MSL.  The


 SNIP....
computed
your fuel burn rate, multiply the Gallons/hour to turn it into
pounds/hour
and then divided by 0.55 to get a fair estimate of your HP.

Best Regards

Ed Anderson


Chuck wrote:

Ed, Sorry for not responding sooner, but I wanted to try a few thing
first.
I am still trying to find out why I am down on power. Since 1-1-2001 I
have
tried:

1.      Installed new engine because the old one was using too much oil.

2 I now get 5100 RPM static and 5800 RPM WOT but still
getting 153 KTS top speed. I took your suggestion and measured fuel burn
for
1 hour at 8000 feet WOT and used 8.5 gallons. By your formula, that
works
out to about 95 HP


  Hi Chuck, 95 HP at 8000 ft works out to approx 126 HP at sea level and
that is bout the same performance I got on about the same power.


. I am at 3000' MSL here, but I don't think that accounts

for that much difference from your burn of 14GPH static.


I agree, it might lessen it by approx 1 gph at same AF ratio.  If I am
getting 156HP at sea level then I would get approx 144 at 3000 msl static


I am working on a
new larger throttle body and maybe will make a new intake plenum as
well. My
throttle body is now 2 1/8" ID. I am losing 1.3" MP. I removed the K&N
air
filter and it made no difference, so maybe 2 1/8" is too small like Paul
told me at Copperstate.


I agree with Paul, I think 2 1/8" is on the low side.  I used two 2" dia
thoat throttle body on the first engine which I think a little too much.
But, I now use the three 45mm throttle body opening on the new engine and it
does not stumble.


I am also trying some intake cowling mods to try and reduce drag, but I
need
to stop experimenting for a bit so I can be ready for a Long cross
country
to Sun-N Fun! I hope to meet you there.

Chuck Dunlap


Great look forward to meeting you at Sun & Fun,. Chuck

Ed

The stumble thing is a programming/sensor responce issue. Any engine needs
a slightly richer mixture when the throttle is slammed open.
That is why carbs have accellerater pumps.

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org