Subject: FD Auto Starter/Bell Hsg was RE: Cosmo Starters vs RX7Starters
From: Paul
Date: 3/27/2001, 3:49 PM

marc wiese wrote:

Hi, Leon-
I've been away with the wife for a long weekend so the reason for the late
reply.
Yes, there are quite a few FD automatics in the USA, and it is shown in the
shop manual released here. In fact my wife has one. And we here often see
them for resale at lower prices than the stick. About 1/3 to 1/2 the FD
sales in the usa were automatics. (heavy traffic, I guess, promotes
'shiftless' people I suppose? And the car's looks appealed to many women
who generally don't like to shift when they don't have to, like my wife!).
They should have thrown in a cupholder with the automatic! Go all the way!!!

To answer your questions about the FD automatic engine (my 20B is
identical). [All dimension and locations are "approximate"]:

1. The rear iron housing is a different casting than the stick FD, having a
cutout for the starter, dimensions are approx. 1-1/4" deep from the rear of
the housing toward the front and 3-3/8" high. The starter straddles the
rear housing and bellhousing attaching to each at two places. The rear iron
housing has 2 locater pin protruding sleeved threaded bolt holes that
locate the starter to it. The starter projects "frontward" on the "car"
(meaning toward water pump) underneath the rear rotor housing spark plugs.
There is very little projection "rearward" toward the bellhousing. This is
the same starter on the 20B and 13B FD automatic.

2. FD auto /20B rear casting bolt holes (identical):
As viewed from rear flywheel looking "frontward" (plugs on left side)-11:00
o'clock threaded; 1:00 o'clock threaded; 2:00 o'clock guide pin (threaded?)
hole; 5:00 o'clock (lower right corner of engine)-threaded; 7:00 o'clock
(lower left) guide pin (threaded?) hole: then comes starter cutout; then at
10:00 o'clock threaded hole. That's it. There is no hole at directly 12:00
o'clock. There is no cutout on the top of the rear iron housing,
either.  At the face of the bellhousing/rear housing the starter would
block a casting extension for an aircraft motor mount from about 8:00 to
10:00 o'clock. However, toward the rear of the bellhousing (tranny side) it
would not be blocked. One could be put there.

3. FD/20B auto bellhousing (identical at rear engine housing):
See bolt hole locations above. The bellhousing has a rectangular access
plate hole at the 6:00 o'clock position (I didn't measure it). The starter
is accomodated by a cutout (2-1/2" deep [from front of casting] x 6-1/16"
high) and machined facing in the bellhousing measuring 3-3/32"  x 7-1/8"
high. When mounted, the solenoid on the starter would project out about
5-1/4" from the face of the engine housing. On the intake side the
bellhousing has an untapped lug hole that is not used. A tin plate
dust-cover  is screwed to this side of the engine and bellhousing.

4. The stock car FD engine mount is by 2 motor mount arms that bolt to each
side the bottom of the rear housing/oil pan with 3 bolts each. This appears
to be the same in the auto as the stick FD.
5. The 20B uses motor mounts bolted to the sides of the iron housings at
the bottom edges, not the bottom.

I had originally intended to mount an adapter plate to the front of a stock
auto bellhousing and include mounts on it. Of course that would require a
longer shaft for Tracy's redrive. If there is enough depth in your proposed
bellhousing to include those mounts on it and still clear the auto starter
arrangement, you have a customer here.

I took some film snaps of the parts and when I get them back and scanned I
will send em along.
Marc Wiese


 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org