Subject: 2.85:1 psru ratio
From: Paul
Date: 3/30/2001, 4:21 PM


"Bass, Jerry" wrote:

RV6A  2.85:1 Ross reduction drive which I added a internal thrust
plate.
Pix on previous msg.

Jerry Bass

Thanks again Jerry. Now I know why you are getting 7000 RPM. Ought to
be
fast.

Paul Lamar


Tracy Crook wrote:

Great climb but Fast?  I haven't seen this ratio go fast on anyones
airplane.  It is almost impossible to find a high speed prop that will
work
correctly at the resulting prop rpm.   I have cautioned all who would
listen
that this ratio will result in low top end and high engine rpm.

Tracy Crook
tcrook@rotaryaviation.com
www.rotaryaviation.com


Come on Tracy. Theoretically it is not impossible to find a fixed
pitch prop that will make this airplane go faster. Back in 1933 seaplanes
were going 400 MPH with a fixed pitch wood prop. Now the takeoff distance
is another matter :-) The other issue is the shape of the HP curve.
If the HP peaks at 6000 RPM then yes. Obviously it is not peaked
at 6000 RPM because Jerry is climbing out at 7000 RPM.

Further more Butch, Perry, Vance and Bill are on the job and we will soon
have a low cost variable pitch prop. Hang in there Jerry.

Paul Lamar

The key word in your message is "Theoretically".  I agree that in theory,
the longest, slowest turning prop is the best. We live & fly in the real
world and there, is is very hard to find the prop for Jerry's plane & gear
ratio.  If you know where it can be found, I and others would like to know.

Tracy Crook
tcrook@rotaryaviation.com
www.rotaryaviation.com


I don't off hand but you can always make your own prop. Many people
have. George Graham and Perry Mick come to mind. Also
if there is enough money involved some of the prop makers would make
you a custom prop I am sure. I know Klause would. If diameter is a problem
due to landing gear limitations you could go to wider blades or a
three blade prop.

BTW what is intrinsically wrong with cruising at 6000 RPM? We don't
really know the limits of the rotary engine. For all we know it will
cruise at 75% power at 6000 RPM for 2000 hours. The four rotor Lemans engine
ran with this RPM schedule for 24 hours with little or no wear.
This engine is still winning races ten years later.

It sure is easy to get a lot more power at 7000 RPM then it is
at 6000 RPM. A lot of the gyro guys running rotaries are running 2.85:1
PSRU ratios with multi blade Warp Drive props. They don't seem to have
any engine problems.

Paul Lamar


I 100 percent vote with Tracy on this issue. I strongly urge people with
potentially fast planes to go with
a ratio that will give them at least 2700 at the prop at top power and speed. The
steep pitched props
churn helplessly at low forward speed, and you will be outclimbed by an
overweight buzzard that
just finished a whole cow. Save those ratios for Storch and Helio Courier
replicas. (and stationary
top speed gyros :-)  no insult intended guys - you obviously can have a lot of
fun below 100 mph too)
- Vance

Hey who needs to get off the ground in 500 feet? Plenty of airports
around with 5000 feet. Look at Perry Mick! He is having fun and talk
about no thrust down low! Sheesss! I would gladly trade another
1500 feet of runway for another 25 mph top end.

Well Vance if you had designed in longer landing gear on the silly Kis Cruiser I could
have used a larger diameter prop instead of just more pitch :-)

BTW I dropped off a couple of carbon fiber blades for you to look at
over at Rich's today.

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org