Subject: flying 700 nautical miles to cma
From: Paul
Date: 5/7/2001, 2:09 PM


Well guys you will never guess what it was. Had Perry and me going for
days.


Broken tension bolt. Perry had the 35 pound flywheel in there which did
not even slow down. Just bent the bolt over at 90 degrees when it came out
of
the hole and contacted the flywheel. Could have seized the engine if it
had
been an auto transmission flex plate. Best to drill the headsof those
bolts
and safety wire them. This is a well known problem with early necked down
tension bolts. Racing Beat recommends coating them with RTV before
installation to damp the vibratory modes.

Perry really scared himself on the last test flight.

Paul Lamar

Scary is right!!

    So the additional drag of the tension bolt presumably caused the engine
to work harder to produce the same amount of prop speed and this caused the
engine to overheat?  Not certain exactly how the bent bolt equal higher
coolant temps otherwise.

    I noticed on the 87 turbo II block I have in the work shop that the
heads of the tension bolts are covered with a thin sheet of steel held down
by the stationary Gear bolts.  I am told that the racing crowd often does
this to prevent the tension bolts from backing out.  It might be easier to
do than drilling all the heads of the bolts.

Glad you and Perry, discovered the problem.  Yes, a flex plate would
certainly have not got the best end of the encounter.

Ed Anderson

Once the bolt bent 90 degrees it did not contact the flywheel. The engine still
generated the same amount of power on take off judging by the RPM.

The big thing here is the fact that when the engine overheats you MUST immediately
shut it off or you will ruin the rotor housings. In the air you cannot always land 
immediately for rather obvious reasons. Even if you are over a controlled field you cannot
usually land immediately unless you declare a full blown emergency. You are between a 
rock and a hard spot. If you do land shut the engine off as soon as you can be sure
you are going to make the runway. Taxing back is out of the question.

Perry and I came up with an emergency cooling system idea consisting of a aux coolant
tank with a couple of gallons of coolant and a high pressure pump (EFI fuel pump)
to inject the aux coolant into the pressurized engine cooling system.

There are several scenarios for a failed cooling system.
this applies to any liquid cooled aircraft engine and not
just the rotary.

A. Water pump failure. Little can be done in the air.

B. A leak in the system somewhere. Temporary transfer of coolant
out of the aux coolant tank will buy you some time to find a place
to land.

C. Combustion gases leaking into the coolant system. The plan for situation 
B should help. Also route coolant from the overflow tank back into the engine
using the high pressure pump. Why pump it overboard to be lost forever.


Along the lines of an ounce of prevention is worth a pound of cure
these are the things you can and MUST do.

1. Number ONE!!!! Use AN line or wiggins couplings in the water system
ONLY !!!!!. No hoses and hose clamps!!!!!!!!!!!!!!!!!! Perry developed a leak
in the cooling system at a hose clamp joint. See the picture below.

2. Pressure check the cooling system before starting the engine.
Once the engine starts there are too many variables to rely
on the cooling system pressure gage to give you a true story.
At that point in time it is too late to detect leaks.
They may not show up right away.
The coolant could be heating up and expanding faster than it is 
leaking out maintaining the system pressure fooling you in the 
process and making you think everything is OK.

Perry came up with the idea of using one of the heater outlets
in the rear housing as a way pre-flight pre-engine start pressurizing 
the coolant system with a small 12 volt electric tire pump compressor 
available in any auto parts store. A tire tube schrader valve will ensure
it won't leak system pressure after you turn off the compressor.

See the picture below of a device I made to bolt in place of
the stock Mazda  pressure cap plastic fitting. This just
for trouble shooting. A method of doing this should be built
into the system.

More about all this as we go along.

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.

http://home.earthlink.net/~rotaryeng/            http://www.linux.org