Lonnie Wood wrote:
Lonnie Wood wrote:
Spring washers on the prop bolts of wood props were
discussed at
one
time
on this
list. Has anybody tried this approach? If so, what part
number
and
spring
rates are you
using?
Lonnie Wood
Lonnie,
This might work. To keep the bolt in tension to prevent fatigue
you
would need
to stack up bellville washers (same direction) until you can
reach
full
rated torque
on the bolt without flattening the stack (they add spring rate
this
way).
If there is
enough travel with a single (set) of washers this might be all
you
need.
If
you need
more travel to accomodate the wood expansion, you would make an
identical
stack to the previous one but revers the whole stack. This
doubles
the
travel with
the same spring rate. You'll need a thick HARD washer to top off
the
stack.
Imagine three (or whatever) washers cupped side down, then
three
cupped side
up and then a large hard washer and then the nut. Getting a bit
complicated, but
should work. You also want a hard surface (hardened steel
washer?)
on
the prop
side.
Bill Freeman
Thanks Bill for your response. I am trying to figure out how much
tension is
on a
3/8 by 24t prop bolt. I could not find any charts. In the "Firewall
Forward" book
Tony recommends 24-28 ft.lbs. but also says this may be too much
depending
on the density of the wood.
Here are my calculations, correct me if I am wrong. 1" divided by
24tpi
gives a
nut travel of .0417" for one complete turn of the nut. If a 1 foot
arm
is on
that nut
then the end of that arm travels 75.384" (pie x 2' x 12") to the
nuts
.0417".
This gives a mechanical advantage of 1808 to 1. Assuming a torque on
the
prop bolt of 25 ft.lbs. this is a bolt tension of 45200 lbs. I
understand
that
only about 20% of the torque goes into tension though from thread
friction
and head friction, so that would leave 9040 lbs. That still sounds
like
an
awful
lot.
I have downloaded some .pdf files from
http://www.bellevillesprings.com/
but a weird thing happens when I view them. The charts go blank when
I
scroll down. I am downloading the latest Acrobat reader to see if
this
will
fix that.
Lonnie Wood
Lonnie Wood wrote:
I have come up with a Belleville part number that might work for this.
CW2310525.
It has a max rating of about 5000 pounds. I.D. 10.5mm O.D.23mm. I have
not
been able to locate a source for these yet. All of the places I have
checked
so
far have spring washers but no where near this load rating. I have an
inquiry into
Belleville to see where to get these. It looks like they are a British
company.
Anybody know of a source?
Downloading the latest Arcrobat reader fixed the viewing problem.
Lonnie Wood
Lonnie, you can stack Belleville washers to get higher loads.
Try: W.M. Berg (800) 455 BERG http://www.wmberg.com
Stock Drive Products (516) 328 3300 http://www.sdp-si.com/
Paul Lamar
Paul,
I have the Stock Drive Products catalog, no go. Also no go on Berg. I
figure I will have to stack at least 2 of these heavy duty washers, maybe 3.
I have found a lot of sources for regular spring washers but most are only
rated at about 350 pounds in the 3/8 or 10mm size. It would take
a pretty big stack of these and a pretty long bolt to handle them.
Lonnie Wood
McMaster Carr cat 105 page 3043 .380 ID, 1.125 OD, load 1220 pounds,
.078 thickness. They have others with a larger hole about the same
rating. You will need three or four making the bolt about a 1/4 inch longer.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org