Greg Richter wrote:
Well, still racking up the boring hours in flight test but I've got enough
data to post a decent status on cooling, Tracy's redrive, etc. Had a lot
of fun and excitement flying the airplane at 103.2 inches aft of the datum
(never trust the mechanics, always WEIGHT THE BALLAST PERSONALLY) and
trying not to run over students in 152s, but the good news is the 13B runs
great! Looks great on my EFIS too (shameless plug). ;-0
Here's the numbers on the rotating parts:
I've been climbing out at 100 knots to keep things cool with coolant and
oil temps stabilizing around 200 degrees F on a long climbout at 4500 RPM
and 3.5 - 4.0 psi boost. Induction Temp runs around 115 - 120 degrees F
reliably. Today was 92 degrees on the runway at Merritt Island according
to my OAT sensor. Drank a gallon of water in flight (me, not the engine).
In cruise oil/water temps are stable at 185 - 195 degrees F. Induction
temp rises to 125 - 130 degrees at high boost levels (6.5 - 8.5 psi) but
have not exceeded 135 degrees even in 30 minute full power runs. I need to
move the POV to _before_ the intercooler to solve this. Gotta go welding
again! I expect this to drop induction temps at least 10 degrees, maybe
more. Current plumbing has ALL the turbo air going the the cooler, then
being vented. Dumb, I know, but it was easy to do. Now it'll be easy to
redo, change, and do properly. Live and learn (and fly!).
Tracy's redrive has working flawlessly so far, with no problems to
report. It's one thing I don't worry about, although I check gear lash
after every flight and go sniffing for oil. So far, aside from being
unpainted, the redrive is flawless.
The engine has a different sound and vibration pattern in three ranges that
I have learned just sounds different than it does in a car, and that my
Bose headsets modify considerably. Noise reduction on gives a feeling of
motion through the airframe, noise cancel off it's more prop than exhaust,
but the turbo whine is noticeable at higher boost levels.
1100 - 2800 rumbles and exhibits a low-ish, boat-sounding, exhaust
3000 - 4200 smooth with noticeable change in exhaust note, boost comes on
abt 3200
4500 - 5500 exhaust louder, the turbo whine is evident, engine smoothest
Sweet spots are 4500 - 4800 in low cruise, 5200-5400 in high cruise with
boost levels at approx 4 psi and 6.5 psi respectively. Cooling is good at
both levels, with the induction temp being the gauge to watch. Paul noted
that this might be a problem, and it is marginal. Prolonged high boost ( >
6 psi) operation causes this to climb. Coolant/Oil temps are stable in the
190-200 range at all power levels, cooling to 180 below 4500 RPM when the
thermostat starts cycling.
I've been babying the engine for the first 10h or so to get a feel for how
everything feels and what is and is not "normal". I started the week at
12.6h and have since opened up the envelope considerably and have done some
full power take-offs at 8 psi boost. Whew! That makes things
happen. Today the Hobbs closed at 21.4, so I've got a few more hours to do
before we can call the program successful. Planning to fly most of the
next three days and wrap it up. I'll keep everyone posted and will be
taking more data as it happens.
For sure we have learned a few things:
Turbo 13Bs can be done, and seem to work so far.
Cooling can be done without fans, and can be made to work
This engine building gig is a Whole Lot of Work, but a Whole Lot of Fun.
-GR
Cozy N722 -- Mazda 13B
Turbo http://bluemtn.com/greg -or- http://bluemountainavionics.com
My info says a 13B at 8 psi boost is making 252 HP at around 6000 RPM.
Got any EGT's for me Greg?
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org