Subject: New cast aluminum 4 port intake manifold.
From: ACRE NL
Date: 6/27/2001, 9:31 PM


 Been agonizing over this for quite some time now.
 I considered using the lower portion of the 4 port
 turbo manifold and milling it off low enough so I could get
 a standard 2.5 inch radius 1-1/2 inch diameter tubing bend
 in there. The Kis Cruiser is quite a problem as there is a
 minimum amount of distance between the thrust line and the top
 of the cowl. The intake runners must be right down on
 top of the rotor housing. 2.5 inch radius bends will just
 barely fit.

 Well I tried that and the holes
 I got in the shortened stock intake manifold were not even close
 to round. :-(. There would be a big problem getting a good match
 between the 90 degree bends in round tubing and the those weird holes.
 See the picture below.

 Besides that the bends alone would cost $25 apiece for a total
 of $100 for all four. That would off set the cost of a cast manifold
 with all the bends cast in.

 The next idea was to get a real big chunk of
 3" by 4" by 12" long aluminum, bore eight big holes in it and carve
 out runners that transition from the ovals in the end housings
 to round pipe 90 degrees away with a die grinder. Real heavy
 and a tremendous amount of work. :-(

 I finally said the heck with it and I have decided to have this casting
 made regardless of the cost. I will only buy ten so if anybody
 wants one of these let me know soon. I will require a deposit
 just before I have them cast. I have a meeting with the pattern maker
 tomorrow so the design might change. This will work stock
 turbo or no turbo. It will accept a simple rectangular flange
 with four tubes welded in for intake runners.

 Paul Lamar

Paul,
I am interested, especially with what the pattern maker changes. I have the
same low clearance problem that you have.

Have you considered composite?

Bill Schertz
KIS Cruiser #4045

Thanks Bill any sales will off set my cost.

The clearance problem is so bad that I had to hacksaw off the two machining 
lugs on the tops of the rotor housings. Gave me another 1/4 inch. 
I had to group both tubes from one rotor directly
over the corresponding rotor housing or I cannot get the tubes low enough.
If I try to pass them over the center or the endhousing they are too high
and interfere with the stock cowl. 

It is easy to use 180 bends and pass
them over the center and endhousing. The matching problem with the 
vertical oval ports becomes severe when you tilt the tubes towards the top
of the rotor housing. My friend John Lynch tried to model the runners in
Pro Engineer and Solid Works. No luck! A good pattern maker can eyeball
and carve the core patterns like an Italian sculptor. That is
why the casting on Ferrari's and other Italian cars are so mechanical 
beautiful. Its in the genes :-)

This is why I finally gave up and bit the economic 
bullet and decided to cast an intake manifold. I guess I am a
perfectionist when it comes to fluid flow aerodynamics.

For a normally aspirated engine you could use a wrap up type intake
manifold and keep it on the same side of the engines as the end housing
intake ports are on. There would be plenty of room over there. The turbo
on the other hand takes a lot of that room.

Yes, I gave a lot of thought to composites and they would work while the
engine was running and cool air was flowing through the tubes but once 
the engine stopped I was worried about heat soak from the hot turbo.
Also the turbo heats the intake air necessarily in the process of  
compressing it which does not help.

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org