Subject: Belt PSRU ??????
From: ACRE NL
Date: 6/28/2001, 10:26 PM


 >The big problem with a belt drive is they waste precious space
 >inside the cowl by
 >uselessly lowering the engine. This almost precludes using one rad
 >under the engine.
 >It gives more room of course over the engine which is of little use in most
 >airplanes. In only a few designs like the Kis Cruiser and the Lancair
 >320/360 is room above the engine real tight and that only by an inch or
 >two.
 >
 >Paul Lamar


 Bill,

 I'm using a chain drive with 5.5" offset. This allowed me to lower
 the engine 3 inches to fit under the Tailwind cowl which slopes
 downward on top and  still have room for the oil filter and water
 pump outlet without modification while at the same time gaining 2
 inches of precious prop clearance.  To fit the planetary gear drive
 under the Tailwind cowl I would have had to lower the engine one
 inch, relocate the oil filter, modify  the water pump outlet and give
 up one inch of prop.     To give up the security of Tracy's proven
 unit was very hard to do.     Jerry


Ah So! This is why you cannot get a rad under the engine.
I understand now :-)

The oil filter is a minor relocation problem.
I take it you still had to move the alternator.

Cutting down the water pump is not much of a problem.
Especially for a welder. See the picture of the
pump I cut down. I used a machined tube but the trick is
to weld the hose barb back on that you cut off in the first
place.

You should have used a 14 inch spinner and placed a half cone
on top of the cowl :-)

Paul Lamar


Paul, There are lots of reasons I did not want to put the rad
underneath.  The under the engine installation is far from proven,
needs a bigger cowl (more drag).  I don't like a  cowl stuffed with
so much stuff that you can't get to anything easily.  Might even have
to remove the rad to change the oil!  The half cone on top of the
cowl doesn't sound cool to me and what a lot of work.   The way I am
doing it, I can buy a Tailwind cowl, use a stock water pump, leave
the oil filter as is, swing a longer prop, and kick ass on top end. I
even have a great place front and center for the oil cooler.  All the
pieces of a good installation seem to be in place.   After taking a
lot a measurements, scratching my head still I bled, I realized that
my problems would all go away if I could off-set the prop.  At that
point I sold my  Ross and started contemplating the chain drive.
 From the beginning, it was clear that the rad had to go in the
fuselage.  Trouble was I did not know how to pull it off.
Participating in this list has been very educational in that regard.

  I think your water pump modification is brilliant but what do you do
when the water pump fails?  Surely, you don't want to go through that
process again.

Here are two pics of my alternater installation.   Still don't know
if the water pump will be as shown without thermostat or back to the
tall outlet with a thermostat.  I got to dream about that some more.
Jerry

I think you are on the cutting (bleeding) edge of aft rad installations
fed by a NACA duct :-) On the other hand there are lots of airplanes
flying around with the rad(s) in the cowl. Some of them even cool well.
(If they seal the hole behind the spinner :-))

The water pump housing does not wear out unless you let the water
pump cavitate. The 15 year water pump cartridge itself is unchanged.

Is that a stock alternator or an extra small one?
Nice trick for lowering the alternator.

If you run the engine with out the thermostat make sure you block
the bypass passage. I have a bunch of pictures on the cut down pump if
you need more info on that. Running with a thermostat and no
cowl flaps is not the hot tip for low cooling drag.

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org

Jerry-Hey-alternator-1.jpg

Jerry-Hey-alternator2.jpg