> > > > > > >Jerry Hey wrote:
> >
> > > >> I have room for two 12" wide ducts ten inches apart
which works out
> > > >> to 96 in sq intake. The inlet ramps will be 32.5" long.
According
> > > >> to the text I am studying in wind tunnel tests a
parallel sided ramp
> > > >> showed a sharp decline in pressure recovery at the inlet at Mach
> > > >> numbers between 0.75 and 0.82 while this did not occur
with the NACA
> > > >> divergent wall inlet until Mach 0.90 was exceeded. Am I wrong in
> > > >> interpreting this to mean that these two designs perform about the
> > > >> same as long as I stay below Mach .75 (around 500 mph)? Jerry
> Jerry,
> The little bit of info about parallel wall NACA
> ramps being as efficient as divergent walls will save
> me a lot of work. I plan to put my radiators in wing
> strakes behind firewall on my "Delta" and had not seen
> info about parallel walled ducts being as good up to
> about .75 mach(I should be able to stay under that
> speed).
>
> -- Thanks
> Kelly Troyer
> Dyke Delta/13B Rotary Power
Ken Powell wrote:
Jerry,
I think that your openings are large enough. Fred Morino's
research showed that we need ~50 sq in for the radiator and 25 sq
in for the oil cooler to cool 160 HP. Fred also stated that a
larger radiator will result in lower drag. Your BIG radiator
should show a lower drag than smaller radiators, i.e., you will
have less cooling drag than a 600 cu in radiator.
Ken Powell
kenpowell@aristotle.net
Ken I think Fred was assuming an ideal duct subject to full dynamic
pressure. I think the duct efficiency number mentioned was 80% of
full dynamic pressure. I don't see no stinking high pressure on the bottom
of these fuselages :-) If anything it is on the low side.
The reason the NACA ducts work so well on pushers is the duct is under
the wing strakes in a high pressure area and the prop
is sucking out the air. Even the P51 scoop took advantage
of the high pressure area under the wing.
I think Jerry needs to test this before he builds it and perhaps
before he becomes highly disappointed. He could mount the fuselage
up side down on the back of a pickup truck.
Geezz!!! As I have said, the worst case scenario is that I will have
to add scoops over the intakes. But since this is an aluminum belly
pan and I will have full access to the rad installation, I could
take the entire intake/rad assembly off the airframe in an hour and
then stick the rad under a bulbous cowl with gigantic inlets.
Frankly, Paul, I think you may have developed tunnel vision as far as
this "solution" is concerned. Your Kiss Cruiser must not have more
drag than the Lycoming version. If it does, you will have proven
that the rotary is not a practical alternative.
Well there does seem to be some compromise when it comes to water
cooling. Perhaps we have not yet developed it fully. I await
cowl pressure data from Finn, Ed Anderson and Tracy before
I am willing to admit that. My main tractor man Chuck Dunlap
seems to be the most advanced. How is it going Chuck?
My inlets are somewhat oversized according to my intuitive sense
of proportion. You may laugh, but I would reject in a New York
minute, an out of proportion solution generated by mathematical
assumptions. I have to work to a vision of the final outcome. That
is why I have done nothing on my airplane for six weeks. The vision
was not clear. Now it is nearly complete.
One last thing. Since I am not running the exhaust pipes
underneath, and do not need an exit tunnel on the bottom of the
cowl, there is an opportunity to shape the belly from the spinner
back to facilitate the efficiency of the submerged intakes. One
possibility is that one could even use the conventional cowl intakes
and pick up the air for the fuselage mounted rad from where you would
normally have the cowl outlet. This would even eliminate the submeged
intakes!!! Remember that you heard this from a dreamer, not an
engineer. It will be fun to contemplate. One thing for sure, my
fuselage will not be flying inverted on top of a pick-up. Thanks for
the suggestion, though. Jerry
Actually that is not a bad idea Jerry. The P47 was built like
that. The turbo and intercooler was in the aft fuselage and
intercooler cooling air and intake air went down a long tunnel under
the entire airplane. The cowling had a big oval hole in front that
ingested all air. The P47 was no slouch speed wise.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org