Subject: NACA Ducts (one last time)
From: ACRE NL
Date: 7/6/2001, 2:26 AM

Jerry Hey wrote:

 Geezz!!! As I have said,  the worst case scenario is that I will have
 to add scoops over the intakes.  But since this is an aluminum belly
 pan and I  will have full access to the rad installation, I could
 take the entire intake/rad assembly off the airframe in an hour and
 then stick the rad under a bulbous cowl with gigantic inlets.
 Frankly, Paul, I think you may have developed tunnel vision as far as
 this "solution" is concerned.  Your Kiss Cruiser must not have more
 drag than the Lycoming version.  If it does, you will have proven
 that the rotary is not a practical alternative.

Well there does seem to be some compromise when it comes to water
cooling. Perhaps we have not yet developed it fully. I await
cowl pressure data from Finn, Ed Anderson and Tracy before
I am willing to admit that. My main tractor man Chuck Dunlap
seems to be the most advanced. How is it going Chuck?

    My inlets are somewhat oversized according to my  intuitive sense
 of proportion.  You may laugh, but I would reject in a New York
 minute, an out of proportion solution generated by mathematical
 assumptions.  I have to work to a vision of the final outcome.  That
 is why I have done nothing on my airplane for six weeks.  The vision
 was not clear.  Now it is nearly complete.

   One last thing.  Since I am not running the exhaust pipes
 underneath,  and do not need an exit tunnel on the bottom of the
 cowl, there is an opportunity to shape the belly  from the spinner
 back to facilitate the efficiency of  the submerged intakes.    One
 > possibility is that one could even use the conventional cowl intakes
 and pick up the air for the fuselage mounted rad from where you would
 normally have the cowl outlet. This would even eliminate the submeged
 intakes!!!  Remember that you heard this from a dreamer, not an
 engineer.   It  will be fun to contemplate.  One thing for sure,  my
 fuselage will not be flying inverted on top of a pick-up.  Thanks for
 the suggestion, though.  Jerry

Actually that is not a bad idea Jerry. The P47 was built like
that. The turbo and intercooler was in the aft fuselage and
intercooler cooling air and intake air went down a long tunnel under
the entire airplane. The cowling had a big oval hole in front that
ingested all air. The P47 was no slouch speed wise.

Paul


YES!! now I have two  ways to go and I like both of them.  The P-47
version is  sooooo easy.  And it does not add one bit of drag.  The
stock cowl has an intake tunnel to the carb.  I could enlarge this to
get sufficient capacity and just run it all the way back.  This works
well with the Tailwinds shape and structure. The tunnel aft of the
fire wall would be in the wind shadow of the bottom of the cowl.
The regular cooling intakes could be eliminated.       I will get the
rad asap and get it mounted,  Then I will mock up the various intake
schemes and have a look.  I should have my drive in a month.  With it
installed, the cowl can be developed.  Things are started to roll.

I have read on this list that the thinnest rad cores were the most
efficient.  I based my rad design on 1" tubes in two rows.   In one
of your recent statements, you recommended using  1.25" tubes as
these would flow better.  I can choose between a 20" square 1" two
row   or an 18" sq 1.25" two row.  They are roughly the same
capacity.  Which would you recommend?  Thanks,  Jerry

  Jerry

I would not exactly say it does not add one bit of drag.
The frontal area of the aircraft is increased and there
is skin friction inside the tunnel. The frontal area of
an aircraft is defined as the max cross sectional area which
does not necessarily occur at the front of the aircraft.
It is going to make the Tailwind look a bit more like
a Howard DGA.

I was referring to the water pipes that conduct the coolant fore
and aft to the radiator from the engine.

It is true however that the thinnest rad cores are the most
efficient. I would go for the 19" by 22" with either
1 inch flat tubes or 1.25 inch flat tubes with two rows to save 
money as this is a stock size :-) Mainly because I am cheap. How 
much money have they quoted you so far on the 20" square design?
 
Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org