Not my idea. The LS1 Corvette V8 engine was the first to use it
I think. It is now universal in almost all V engines built around
the world. The curved runners do not appear to hurt or nobody
would be using them. If you inject fuel it has to eventually go
down the runner sooner or later. It does not just disappear.
If it evaporates all well and good. That is ideal mixing
of air and fuel. That is the whole point of injecting
it at the start of the runners.
The auto guys inject it close to the engine for better throttle
response reasons.
The other thing about tuned runners is the engine tends to get
the best BSFC at the tuned length. So for best BSFC it should
be tuned for cruise RPM. This should really show up when
we get a variable pitch prop and we can run the engine at
wide open throttle at say, 4500 RPM. Its like having overdrive
in a car.
Paul Lamar
Monty Roberts wrote:
One thing you guys might want to consider about fuel injection points is the
difference between carburated manifolds and fuel injection manifolds. One of
the reasons that fuel injection works so much better is that you can design
the runners for dry gas flow. When you have to take into account two phase
flow around bends, and subsequent fuel seperation, it changes how you design
the manifold. Throttle response is one of the main advantages of placing the
injectors close to the port, but it also allows more flexibility in runner
design. If you inject fuel into a coiled intake it can puddle or come out of
suspension. This can result in erratic mixture, and can also accelerate wear
by flooding the cylinder walls with gas and destroying the oil film (not
necesarily applicable in a rotary with oil/fuel mix.) But the erratic
mixture and fuel puddling, two phase flow stuff still applies. Maybe not as
much in a two rotor constant speed engine vs a multi cylinder racing engine,
but it should still be taken into account. If you do inject the fuel
upstream of the manifold, you will want turbulent airflow in the runner (a
nice sand cast finish is good, not mirror smooth) and large smooth bends
with a raised roof. You don't want a big slug of fuel entering the rotors
just as you firewall the throttle after hitting big sink on short final.
-( or maybe {:O.
Monty
Puddling can happen Monty but it is unlikely as we have one runner
per injector. If it puddles in only one runner there is something wrong
with that injector as all runners are the same. It is just plain unlikely
unless there is a problem with the computer and an over rich shot of fuel
somehow makes it out of the injector. This too is a bit unlikely as the
injectors are limited in flow. That is one of the reasons we use four
instead of only two. If the engine is not turning over and sucking air the injectors should not be injecting. Also the wrapped up manifold is going
to be quite hot on the bottom where puddling would occur most of the
time as it is located directly over the red hot exhaust manifold unlike
in a piston engine. This will vaporize any puddles of fuel for sure.
In a turbo engine it is difficult to inter cool the air below about 130 F.
The puddling problem was a big problem back in the
days of single carbs or a single throttle body fuel injector used a
few trucks. People could pump the throttle so the accelerator pump
in the carb could squirt raw fuel into the manifold when the engine
was cold and not running. Carbs where always and still are mounted
at the beginning of the mostly unsymmetrical runners in a typical
piston engine manifold.
Mounting the injectors at the beginning of the runners is not essential
and if you are worried about it don't do it. It just gives a
small percentage reduction in fuel consumption due to better mixing
fuel and air and gets the injectors and fuel plumbing over
on the cool side of the engine in a non wrapped up manifold.
I would guess less than 3% reduction in fuel consumption.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org