<< I guess, I don't understand this search for a different coolant medium.
> So far as I know, no commonly available liquid has a higher specific heat
> value than water. Even mixing antifreeze with water effectively lowers the
> amount of heat the coolant can absorb as antifreeze does not have as high a
> specific heat value as water. So regardless of the boiling temp of the
> cooling liquid, if the specific heat value is lower then less heat is
> transported from the metal into the liquid per unit volume. While a higher
> boiling temp does permit more heat to be transferred to the cooling medium
> before it boils, this does not necessarily mean that it transfers heat more
> efficiently than water. There may be some applications where the higher
> boiling temperature is critical, but for ours? What am I missing?
>
> Ed Anderson
I think it is the result of a misspent youth. Too much band practice, and not
enough working on hot rods and drinking beer. It may be a growing wives tale
that rotaries have a cooling problem. I think it is a bleeding problem. I
have taken to holding on to the water outlet during the first run, to be sure
that the pump is moving water. There are many nooks and crannies where air
remains trapped after filling with coolant. The very old engines had a sensor
hole in the flat spot on top of the center cast iron. I put my water temp
bulb in that hole. On fill up I would open that hole and let out almost all
of the air. If you don't, a slug of air will park in the top of the block,
and sit there while you try to figure out why you didn't buy that Lycoming.
If you rev the engine up a bit, and the pump has enough water in to hold a
prime for a second or so, it will snatch that slug of air into the pump, and
then everything stops. If your hand is on the water outlet on top of the
pump, you will notice that the outlet is not getting hotter. The pump is
mounted high on the block and when the engine burps, the air stops in the
pump.
Shut it off. What to do? Well, you can open the hose and let the air
out. You can run a swirl pot as is done in industry. Rollairtrols they are
called.( I used to build heat transfer packages). You can put an air bleed in
the top of the water outlet. If the installation is going to make breaking
open the top hose impossible, then an air bleed it the top of center section
will be required. This should be a minimum of dash 4. This would run to the
bottom of a make up tank (as used in industry). They are called "make up
tanks").
You can have fill ports at handy locations around the system. The
fill port(s) are just caps, no pressure relief's. The high spots are all run
to the bottom of a pressurized bottle, that has the 16 or 22 pound Stant
lever cap on it. The bottom of the recovery bottle is plumbed to the outlet
of the pressure bottle. The pressure bottle is kept 1/3 full of coolant. As
the engine heats up and coolant volume increases, the excess coolant and air
from the high spots moves to the bottom of the pressure bottle. The air pops
to the top of the bottle. When the coolant changes volume (cools) only liquid
coolant can be recovered from the bottle. This is not the cooling and volume
change that occurs on shut down. It is the normal change associated with
power changes. These pressurized make up bottles were used on early (that I
know of) RX-2s and RX-3s. Toyota also used them. They work great. It takes
several sessions on the track to get all of the air out of the race engine.
It is very hard to do. Not doing it will be very$$$$$. If you run a
thermostat, drill a couple of 1/8" holes along the upper edge of the flange.
Or cut a "V" notch out of it. Otherwise it will not let the air out of the
engine. The air trapped under the thermostat will not let coolant heat the
thermostat so it will open. Believe me now for free, or believe me later for
big bucks.
Lynn E. Hanover.
Very very good description of what is going on in there. Best I have seen.
Thanks Lynn.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org