Subject: Vne - was "plugs up/lack of"
From: ACRE NL
Date: 8/26/2001, 1:23 PM


< snip >

Wow! That looks great Monty. I was just kidding about the under the cowl
renditions and here you have them done.

do you really think I just make this stuff up? ;-)

So cool. You ought to do  a article for the
EAA Sport Aviation magazine on this. Judging by the results Charlie
Airesman is getting this thing ought to be real fast.
Won't be long before someone is going 300 MPH with a rotary at this
rate. You got dimensions on the engine so you can do a 3D on that too?

BTW Butch is getting ready to spring the LAEV variable pitch
prop on the world which you will need.

Paul Lamar

Paul,

Not sure I'm ready to do an article yet. I would rather wait until I have
some hardware to show. I really want to make one of these things that has
the minimum drag possible. I want to shoot for the best efficiency I can
get. That definitely calls for a variable pitch prop. I flew a 182 the other
day, which was my first experience with a variable pitch prop. WOW! what a
difference that makes! I knew it made a big difference on paper, but until
you get the seat of the pants feeling for how much difference it makes you
can't fully appreciate it. A canard REALLY needs a variable pitch prop, and
so does an RV for that matter. I could maybe do an article on the theory
behind designing something like this engine installation. There are so many
different angles I'd have to pick one topic and concentrate on it. Cooling
drag reduction for instance. I don't know if it would be better suited for
Contact! or a more technical type mag.

300 mph would be nice {8O. I'm still a little scared about the airframe. Its
quite a bit faster than Burt's published VNE. I'm sure he was conservative,
but I want to know for sure what the airframe is capable of before I try for
those kinds of speeds. The Berkut has a higher VNE, something like 400 mph
if I remember correctly. So I asume that it would be possible to beef up the
spar etc. to make the airframe capable of those speeds. The Memphis gig
would be a good time to sit down and discuss these things in detail. I'm
sure that Herb can set me straight on this.

I'm waiting for a few projects to pan out so I can buy a new piece of
equipment before I model the engine in detail. It is a 3D digitizer that is
good to within about 5 thou. Plenty good for entering the outer shape of the
engine, etc. It sure beats the caliper and enter method, and is much more
accurate to boot. This coupled with an NC mill should make reverse
engineering all too easy :-)

Monty


Klause is going over 250 with a Varieze but he has discovered some things
along the way. I am sure Herb is aware of them. Klause is also very
fond of beefing things up with carbon.

Paul Lamar


 Exceeding VNE (V *never exceed* !!!) is a VERY risky proposition.  The Berkut
used carbon fiber all over the place and the much higher stiffness and lower
weight
of the carbon will help a lot with this problem.

I'm not an aero engineer, but this is aero-structural interaction and I have
studied it
a bit.  Any real aero engs out there please correct this if I get it wrong.
Apparently
the biggest issue is flutter of the aero surfaces (wings, horizontal stab,
fin)  The
natural vibration frequency of a vibrating object is proportional to (K/M)^0.5
which is the square root of the stiffness (K) divided by the mass (M).  So, to
increase the natural frequency (where flutter can occur), you need to increase
K (stiffness) and/or decrease M (mass).   Carbon is about 3X the stiffness of
glass, so this is very helpful when trying to increase the Vne of an
existing design.
Substituting carbon for glass increases K.  Since most carbon is also
stronger (note
that stiffness and strength are NOT the same, nor are they particularly
closely related)
than glass, you can use less, so you may also decrease M, also good.   This
just tells you
about the general direction you are blindly wandering in - generally towards
death and
destruction or generally away.   Not good enough in my book.   Test pilots
make the big
bucks by going out and finding out whether the calculated Vne is actually
safe.  If you get
it wrong, the pieces are usually scattered over a very wide area.  You
really need to do
a proper ground vibration survey (needs smart people & expensive equipment) to
find out what the whole surface flutter situation is going to be like.

This is very dangerous ground to be working in without proper knowledge.  A lot
of "eyeball engineering" will work just fine up to about 150, perhaps 200 mph.
When you start looking 300 mph in the face, the rules are changing and the laws
of physics are extremely nasty.

Remember the famous saying of one of the 20th century's great philosophers -
Harry Callahan:  "A man has GOT to know his limitations."

My saying is "The laws of physics will be strictly enforced"
 . . . .and they'll kill you in a heartbeat without remorse.

Ya'll be careful out there in the "experimental" part of the flight envelope.

Bill Freeman
Long EZ builder & pilot
BSME, MSME
EAA Technical Counselor

 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org