<< > >Have any of you rotary car racer types tried chrome plating
> >the rotor faces? In theory it should give a bit more power
> >and a little less oil heat.
Paul Yaw polishes them to a chrome like finish. How well it works I don't
know. I have not seen anything used for an insulator at all. Maybe the Lemans
motor had something. Mazda is missing the boat by not assembling a handbook
on engine preparation for the various racing classes. They have all of the
data we need, but provide nothing.
There will be at least three RX-7s in the
GT-3 race at the SCCA national championship races this September. Sundays
GT-3 race was won by Rob Warckoci from Chicago won in his sharp red late body
style tube frame. Sheldon Wilde from Indianapolis was second in his 86 style
tube frame and Terry Whitlock was third in my late style tube frame. Due to a
broken transmission at the first race in Michigan and a broken apex seal at
Akron Ohio, we needed to get in at least 10 laps
to get credit for a finish, for sure, before any racing with the troops was
started.
On the tenth lap the driver equaled his best ever lap. Had we not
held back at the beginning we would have been wedged between first and second
place cars for the whole race. The weekend started poorly with the American
Lemans cars and the TransAm both running at the same time last Saturday and
Sunday. It looked like the entire free world supply of carbon fiber was
there. We were in a field outside the paddock area. There were over 400 SCCA
cars entered. We practiced on Friday morning. The engine is a hodge podge of
blown up motors from the past. The only new parts were "O" rings and side
seals. I told the driver not to go over 8,500 for a few laps, to let the
thing wear in a bit. It broke up so badly that going over 8,500 was no
problem.
It wouldn't go over 8,000. I gapped the plugs shorter and charged
the battery up, checked the jets for any dirt, and found none. Saturday we
qualified 6th in class with the engine running better but not pulling the
revs in top gear. This still sounds like a secondary ignition problem. With
two MSD systems this should not happen. The driver came in to tell me
something I already knew. He tried to refire the engine to go back out, and
nothing..... Battery dead as a door nail. We get towed back to the paddock
and I hear that there had been an accidental shift into 3rd gear instead of
5th, also 5th is not available sometimes. I review the tape to see how high
it went. It never went over 10,000. No problem. We hook up the jumpers and
fire it up. there is a shrill squeal. The throw out bearing has seized up and
for a while the sleeve it is mounted on was spinning on the bearing retainer,
until it ran out of lubricant. Then it spin welded itself to the retainer,
and was now destroying the pressure plate diaphragm springs. No problem... we
take out the transmission, and drive the sleeve and bearing off. I cleaned up
the sleeve and press on a new bearing. I file off the goobers off of the
bearing retainer and we put the whole mess back together. My able assistant,
Mike Canan (retired Police Officer) was inside the car removing and
reinstalling the sheet metal, and throwing tools. We put in a 411:1 rear end
gear (removing the 485:1) and forget about using 5th gear, 1st is now usable.
We fire up the engine and it sounds just a bit flat. I hook up the timing
light and check the leading. No problem, right on 27 degrees. Hook up the
trailing.....Nothing at all. Nobody home. I install another MSD, and test
again. It runs great.
We come back for Sundays race with a new battery and high hopes. The junk
motor ran fine and we got a third place. We are very happy. We finish the
year in 6th place in Central division and an invitation to the National
Championship race in September.
Nothing could go wrong now. Not today. Then my wife took a giant step out of
the trailer, crashed hard and broke her arm. Nothing ghastly..... she would
not go to medical to have it looked at. We are a stubborn pair. So Monday,
AM, are in the emergency room back home for the bad news. She will be OK in
about 5 weeks. But except for that it was a great weekend. The Temps were 180
water (with the thermostat out of the system) and oil 200. Oil pressure was
85 pounds. Peak revs 9,800. (don't do that to a 13B).
Lynn E. Hanover
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org