Subject: Cadillac Vacuum Pump
From: ACRE NL
Date: 9/29/2001, 2:52 PM


    Paul and All,
      Has anyone on the group come up with any numbers
on the Cad. vacuum pump capacity(How many instruments
it will pull)?

    Kelly Troyer

--
Dyke Delta/13B Rotary Power

Don't think so. Not so far.

Paul Lamar


I don't know it's capacity in # of instruments, but it pulls about a
20-24 psi vacuum so it should be plenty.  Others on the rah ng say
they've been using it for years.

AI Nut

20-24 psi vacuum????? No way!!!! 15 psi is absolutely no air at all.
That is as low as you can get. Nothing there! No air molecules!!
Nada!!!

Paul

 I believe that the gentleman MEANT to say 20-24 inches of mercury.
(This of
course is on a closed system) These pumps were also found on early 80s
Oldsmobile diesels. The Oldsmobiles came with either 4.3L V-6 or 5.7L
V-8
diesel engines. I had a 1983 Olds Cutlass Ciera with the 4.3L V-6. I
know
that there were many problems with the 5.7L V-8 engine. My V-6 ran very
well
and for a long time. I've never measured the capacity of these pumps. I
suspect that it would be more than sufficient though. In my limited
experience, this pump was durable.
Charlie Kuss


This may mean 20 to 24 inches in a water monometer or a tube filled with
water. Put a clear tube 6ft in the air and conect one end to to vac pump and
the other in the bucket of water. this will give the amount of vacuum.this
can be calibrated to mercury and as it is much heavier the lift is much
less. The amount of vacuum can be measure by the time it takes to pull a
volume to a predescribed vacuum.
Regards Don


Sorry for the confusion, huge mental lapse.  Of course, I meant inches
of mercury.  I only have 3 different instruments for measuring vacuum.
1) a vacuum gauge from the auto section at Sears.  This is the one I
used for the 21-24 inches of mercury values.  2&3) The other two are for
deep vacuums that measure in torr units -- both of these units had their
needles deflected only slightly and still stayed in the "atmospheric"
range 8-).

My biggest worry, however, is if the cadillac pump doesn't pull TOO much
vacuum and that it will overwhelm the aircraft vacuum regulator and then
destroy those expensive instruments 8-(.  I take heart, though, that
others have claimed to use these units successfully.  I should probably
test this before I subject the instruments to it, just to be sure.

On a practical note, it appears that the pump works slightly better with
the suction inlet pointing down.  In either up or down orientation, the
diaphram area (?) gets quite warm.  Hope that is normal.  The motor is
huge for a 12V.  Fortunately, the attach points already have rubber
anti-shock mounts installed from the factory, as it does vibrate a fair
amount.

Lastly, one test I ran was to turn the pump off and see how long the
system would hold the vacuum.  No clamps were used so all fittings and
hoses were simply friction held.  The system kept some vacuum for nearly
24 hours, with no discernible drop during the first few hours.  I didn't
really keep a close eye on how fast it returned to atmospheric, but it
held quite well so I assume these are pretty good pumps.  The only bad
result is that now my Sears vacuum gauge is permanently set to 5 inches
of vacuum while open to free atmosphere.  Dang it.  I don't see any way
to rezero it either.

HTH,
AI Nut


The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org