Subject: The piston verses the rotor.
From: ACRE NL
Date: 10/16/2001, 4:14 PM

The Piston Verses the Rotor?  By Paul Lamar

Lets analyze the motion of an aircraft piston engine rotating 
clockwise at 2500 RPM. The bore is five inches and the stroke is 
five inches. At the three o'clock position of the crank the piston 
is moving down the bore at maximum speed. At the nine o'clock 
position the piston is moving up the bore at maximum speed. At noon 
and six o'clock the piston is stopped at top and bottom of the bore 
respectively.  

The circumference of the crank is pi times five inches or 15.7 
inches. That is 1.31 feet.

Since the RPM is 2500 the RPS is forty two revolutions per second. 
So the speed of the crankpin is forty two RPS times 1.31 feet or 
fifty five feet per second moving in a circle. The piston speed is 
therefore the same as the crank pin speed at the three o'clock and 
nine o'clock  positions. 

Bear with me here as we are steadily getting to the point. It takes 
the crank one second divided by forty two or .024 seconds to rotate 
once. To rotate from noon to three o'clock it took one quarter of 
that or .006 seconds. Therefor  the piston accelerated from a dead 
stop to fifty five feet per second in only .006 seconds! The average 
acceleration is then 9200 feet per second in one second. Well now 
lets see. One G is only thirty two feet per second in one second so 
9200 divided by thirty two is about 290 G's!!!!!

Let's assume for the moment the connecting rod, the piston pin and 
the piston with the rings weighs seven pounds. They all move the 
same way the piston does. Mr. Newton said, and he seems to be right, 
force equals weight times G's. The three pound piston alone looks like 
870 pounds to the rod in the form of inertial load.  Mr. Connecting 
rod has to push and pull that 870 pound piston back and fourth once 
every .024 seconds. As far as Mr.  Crankpin is concerned that seven 
pound pile of stuff looks like it weighs about 2000 pounds! 290 G's 
times seven pounds is about 2000 pounds of inertial load. Mr. 
Crankshaft says "OUCH!". This is a simplification of course. The 
compression and combustion pressure loads sometimes add to and 
sometimes subtract from these inertial loads. I cannot imagine
a piston engine  made without light weight pistons.
The piston engine, as we know it today, would not be possible
without aluminum pistons.
 

Metal fatigue happens when the force and therefore so too the stress 
repeatedly reverses on a part. It is no wonder your aircraft engine 
crank shaft and other parts are a mass of cracks at over haul time. 
Its a miracle that piston engines last as long as they do. It has 
taken over 100 years of development and billions of piston engines.

All other things being equal, like intake breathing, the HP of an 
ICE engine is directly proportional to the RPM it can be run. The 
wankel engine breaths extremely well at high RPM's due to to the 
lack of poppet valves getting in the way of the intake and exhaust 
ports. 

You might surmise from this the wankel rotary is able to revolve at 
unlimited RPM's because there are no reciprocating parts. You would 
be wrong. The wankel rotary also has its RPM limits.  Centrifugal 
force rears its ugly head. The weight of the rotor spinning around 
the center of the e-shaft creates a terrific centrifugal force on 
the rotor bearing at speeds of 10,000 RPM or more. By the way the 
turbine engine is also subject to the same centrifugal force limits 
on its compressor and turbine blades. 

Never the less the wankel rotary can rotate far faster than an 
equivalent HP piston engine adding to its intrinsic power to weight 
ratio advantage. Also this centrifugal load due to the weight of the 
rotor  never changes direction on the e-shaft at high speeds so a 
cracked or broken  e-shaft on a wankel rotary is unheard of. This is 
why the wankel rotary engine designer can afford to make the rotor 
out of low cost and extremely durable but heavy cast iron.

Further development of the rotor is possible of course. Better 
casting techniques are used by Mazda to reduce the weight of the 
rotor in the RX8 engine soon to be announced. The RX8 engine is 
rated at 290 HP at 9500 RPM. Not bad for a 200 pound engine twelve 
inches wide, fourteen inches high and seventeen inches long. 

Rotors made from other material with a better strength to weight 
ratio than cast iron may eventually be used. A more costly aluminum 
rotor is possible with steel inserts in the high wear areas of the 
apex seal slots. A titanium rotor is also possible. So too would be 
a sheet steel rotor perhaps laser welded together.

I hope I have adequately got the point across of why the wankel 
rotary is a better engine than the piston engine.

-- Paul Lamar The AirCraft Rotary Engine NewsLetter. Powered by Linux. ACRE NL web site. http://home.earthlink.net/~rotaryeng/ http://www.linux.org