Subject: Lots of apex seal info
From: ACRE NL
Date: 10/19/2001, 5:01 PM

>From http://www.scuderiaciriani.com/rx7/apex_seals.html

Date: Mon, 25 Sep 2000 08:47:49 -0700
From: Michael Gurgainers (gurgainers@blomand.net) 

I have been using Atkin's Rotary's apex seal in the engine I build for some time now. I really like them, as they seat so much faster and cause less
damage to rotor housings than Mazda factory seals. However, I detonated my engine the other day and one let go (totally my fault, I can not/will not
fault the seals). 

I am considering using John Almeida's (sp?) ceramic seals from Powerhouse Engineering. I was wondering if anyone has used these before, what their
opinion is vs the Iannetti seals that are approved by MazdaComp, what is the wear characteristics of the seal, and how much boost was run. I spiked my
boost (accidently, one missed keystroke on the PFC will cause a rotor and housing to turn to slag) to 18psi (ooops) with no other fuel enrichment other
than what was programmed for 12psi. 

I am hoping to prevent this as I have been told by some that these ceramics seals will take much more abuse (having to tune an engine without
realtime, high res A/F ratio monitoring on a chassis dyno constitutes abuse IMHO). Please do not respond if you have not used ceramics seals in your
own motors in the past or have spoken directly with those who have (IE. no hear-say please!). If you have information on these I would like to speak
directly to you via Phone as I have quite a few technical questions if you have the time. 

_______________ 

Date: Wed, 8 Mar 2000 16:09:25 -0500
From: "Eddie Versace" (eddieversace@starlinx.com) 

Ianetti(sp?) stopped making his 3mm seals b/c of too many problems with them, or rather the rotor housings. If either are machined even slightly less
than perfect, it almost always results in another rebuild rather quickly. Stick with 2mm seals. 

_________________ 

Date: Fri, 27 Feb 1998 23:42:01 -0800 (PST)
From: NetBlazer (netb@world.bc.ca) 

Ok does this mean that the ceramics are more durable and all around the best? 

Most will advocate using the ceramic seals for only high boost turbo applications. I did notice that the 3 and 4 rotor Kudzu chasis Can Am cars racing
at Daytona (normally aspirated) were using them. I think the motivation for the above advocation is due to the cost alone. 

The advantages in any engine are that the ceramic material used has a lower coeficient of friction than the more conventional ductille iron seals, and
the material is a lot harder. The lower friction, means less wear to the surrounding parts (apex seal grooves, rotor housings, and side housings), and less
wear to the seals due to both the lower friction, and harder material. The wear characteristics have been described to me as negligable, but initially
enough for them to break in correctly. 

Other advantages, are that the ceramic material has less physical mass, so requires less spring pressure to keep them in contact with the rotor housing
surface at a given rpm, plus due to the lower coeficient of friction you can use more spring pressure without causing an appreciable increase in wear.
Either one of the above means the engine can run at higher rpms without the seal floating, which can cause hot exhaust gasses to travel back into the
intake cycle of the other rotor chamber and cause pre-detonation which is one of the major concerns in any non diesel engine. 

Stock apex seals can overheat, and warp which is not a concern with the ceramic seals. The ceramic seals although not indestructable, can take a lot
more detonation than stock seals. They can also stand up to a lot more boost/power output. 

Now for why people stray away from them: ceramic 2 piece 2mm or 3mm seal set costs $1770, plus in the case of the 3mm seals you have to buy double
the number of apex seal springs. You could go for the single piece 2mm or 3mm seals for $1200, but will have less compression under 4000 rpm over
the 2 piece seals. 

After getting past the 'you don't want those!...why not?...because they cost a lot'....banter, I have heard from several rebuild places, and Franchesco
Ianetti himself that when it is time to rebuild the engine, you can re-use the ceramic seals over and over again (the gift that keeps on giving?). 

I have seen and heard about far too many rotary engines where either the seals break from detonation, or wear out the rotor grooves making the seals
not fit properly, and eventually breaking the corner seals (non solid corner type seals where Mazda thought a piece of rubber might prevent this), and
doing major damage to both the rotor, housing, and turbine wheel. The cost of doing a premature rebuild alone is enough to make the cost of the
ceramics seem like a bargain, plus the cost of the damaged housing/rotor..then add in the amount of pain and suffering you will go through when the
mustang you were racing when the stock seals went beats you :) 

_______________ 

Date: Thu, 11 Sep 1997 21:43:52 -0700 (PDT)
From: NetBlazer 

Well, I have spent several hours talking to Francesco (sp?) Iannetti on the phone (3 seperate occasions mostly on his quarter :) 

He is the designer/owner of the company that makes the expensive, low mass, high strength ceramic apex seals that are only sold through Mazda
Comp. Aparently many racing teams run them, including the Downing team (Rolex 24 hours, etc), Mostly Mazda, Pettit, etc... 

Anyway a set used to cost around $1500. Due to recent material improvments he was able to increase their strength and lower their cost. A set is now
around $50 an apex seal cheaper, so somewhere around $1100 a set. This is very good news as I have been saving up to build my engine (core with
15000 easy miles on it sitting in my garage waiting for 3mm one piece ceramics) 

The advantages are they can withstand higher rpms without floating, they can use a higher spring force than stock, without adding any additional wear,
which gives better sealing. The wear they do cause is insignifigant, and they won't wear out anywear near as soon as stock seals, or cause the same
dammage to the rotor grooves, or rotor housings that stock seals do after high mileage. They can take more detonation, higher boost pressure, leaner
conditions, etc. 

The only downside I have heard of is cost. I think their cost is insignifigant when compared to the cost of new parts when one of the stock seals decides
to break, and tear into the rotors, housings, and turbine blades. Plus the cost of a complete rebuild at that time..OUCH. 

They are available in 2mm one piece and 3mm one piece, and a more expensive 2mm 2 piece and 3mm two piece. The 2 piece will seal a little better at
the rpms you street drivers like, and not any better at the higher rpms. The 2 piece seals are also more expensive. Many street cars are running the one
piece seals with no complaints, and thats what I plan to go for. Also it was mentioned that a customer with an airplane powered rotary did some tests
and found that the 1 piece ceramic seal had higher vacuum than the stock 3 piece seal due to the increased spring pressure. Iannetti's tests have shown
that the 2 piece seal is better than the 1 piece, but the torque difference he quoted me was in inch pounds, and was from a 3 rotor, so I consider it
approx 50% higher difference than our 2 rotor engines. 

Finially he asked me to post his new website address. The deal is he is currently wanting to take orders for a rotor clock that he designed and has hand
crafted, for christmas. (they are made to order and takes many weeks as they are mostly hand crafted and polished). The clock is pricey, but beautiful.
The rest of the site is not finished, but the rotor clock section is complete. I am trying to get him to put up some info on the ceramic seals, but he said
that would take some time to do as he is very busy. Web Site 

>From talking with him I got the impression he loves the rotary due to many of the reasons we love it, and he is in for the long haul, and not ready to
give up on it, even though sales of the apex seals only trickle in. 

                                                          

Date: Thu, 18 Dec 1997 07:09:21 -0600
From: CRASH 

According to Mazda Comp (I asked them if the Lanettis were streetable), the Lanetti seals are much stronger, lighter, able to operate under higher
spring pressures, and even enjoy some self-lubricating properties. They have greater beam strength in a 2mm size than a comparable stock seal in
3mm width. As far as wear characteristics, they are supposedly easier on the chrome lining of the rotor housings than a stock seal. Although few
people use them in street motors because of cost, they are streetable. 

In short, they (Mazda Comp) didn't see any drawbacks, except the high price. 

                                                          

Date: Wed, 4 Feb 1998 15:23:20 -0800 (PST)
From: NetBlazer 

A problem has been discovered by one of his customers relating to apex seals sticking: For more power, it is a good idea to keep clearances tight,
between the apex seals and the grooves. The problem relates to shops who machine out the grooves to 3mm. The procedure is to cut one side, based on
the corner seal, then the other side. The problem arrises when the corner seal is not seated perfectly, which can be caused by casting inperfections in
the rotor (yes the rotors are cast iron), or corner seal. In many cases one side of the groove can be off from the other side, which under load can cause
the seal to bind, and cause it to stick, creating a lost of combustion containment and detonation. 

How they figured out what was causing it: An engine with the ceramic 1 piece 3mm seals was exhibiting the symptoms. The seals were replaced with
softer carbon seals, and the symptoms went away. Then the seals were replaced with the hardened seals Mazda Comp sells and the symptons came back
(same motor). The reason the carbon seals didn't exhibit the symptoms was because they are softer and will quickly wear in the spot that is causing it
to stick, eliminating the problem. Replacing the seals with the 2 piece ceramic seals also eliminated the symptoms. 

I have been told by several people that the 2 piece are going to yield more low end, and are a better setup. I have still shied away because they are not as
strong as the single piece seals. Franchesco said they have done testing on them, and they will take the abuse from a 2 rotor engine putting out 600hp at
the rear wheels (24psi boost) all day... Thats enough assurance for me, combined with the less chance of them sticking. 

To prevent the single piece seals from sticking either make sure the grooves are straight (no-one seems to be able to guarantee that) oand/or machine
the grooves to have .0015" clearance on each side of the apex seal, or .0030" total clearance. 

For the 2 piece ceramic seal, use between .0005" and .0015" clearance per side. 

If you are running Mazda Comps hardened apex seal instead of the ceramics, use the same specs as the ceramics. 

The motor that is making 600hp at the rear wheels has extra dowel pins added to the housings to prevent the sandwich from twisting around.
Aparently Pettit can do this, as well as a couple other places which I don't know yet if they do for other people or not, but will find out before sharing
their info. 

He also mentioned that he got a call from a list member who had heard of the ceramic apex seals off the the lsit, but didn't hear where to get them.
Mazda Comp is the designated direct reseller 1-800-435-2508 

Also note you can get 2mm ceramic apex seals which are also very good, and don't require the machining. The Mostly Mazda race cars are running the
2mm ones at 20PSI boost with no problems. 

The cost is about 4 times that of stock apex seals, but is what I consider cheap insurance considering they will save you 3-4 times their cost (maybe
more depending on the cost of the mods to your engine) the first time they don't break in a situation the stock ones will. Plus your rates don't go up
after you make a claim on that insurance either :) 

                                                          

Date: Sun, 1 Mar 1998 10:06:06 -0800 (PST)
From: NetBlazer 

In most cases the dealers themselves do not rebuild rotary engines, and just swap in MTC (Mazda Technical Center) rebuilt crap engines..oops did I say
that out loud...so they couldn't do it anyway. 

I am biased towards Hayes Rotary, so I will just list a few of the places I know have done them. This list is harly complete. Pettit, PFS, Hayes, XS
Engineering, Mostly Mazda, Redline Performance, Carlos Lopez Racing. 

The last two I do not know if they do work for people off the street, or just their own stuff, and referrals. 

If you are doing the 2mm one or two piece seals, any rebuilder can handle it. If you are doing the 3mm two piece seals, any rebuilder on that list can for
sure, plus any rebuilder who has a machine shop who does their 3mm rotor machining (rotors that came stock with 2mm seals need this) can do it. 

The problem comes from 3mm 1-piece. If they do not get the groove perfectly cut to be in line with the corner seals (often times a casting
imperfection in the rotor could cause a problem) then the seal may bind, and you have worse problems. The same is true for using the 3mm Hardened
carbon seals on a NA engine. The 3mm 2 piece seal which is a very good idea for street/race use anyway doesn't have the same problems with binding. 

Also note, when rebuilding an engine and going with 3mm seals, it is a good idea to go with the 85 13B solid corner seals. Mazda changed design, and
now have a large hole in the corner seal, which they fill with a rubber insert. The corner seal is lighter, but prone to breakage because one side of it is
very thin. 

                                                          

Date: Thu, 5 Mar 1998 00:59:40 -0800 (PST)
From: NetBlazer 

Okay, I now know why they are so expensive...we are paying for the case they come in :) The case is a block of wood, that has Ianettit USA and the logo
burned into the back, on top it is felt lined, and the whole thing is in a plastic sleeve. It's so nice, it sorta seems a shame to put the seals in. I guess I will
have to get a second set to put on my desk :) 

There is also a x-ray of the seals, and I can't see any impurities in it. I would hope no end user ever would. I know Franchesco said every once in a while
there are which is why every one gets x-rayed (obviously pre-screened). 

The seals are soooo smooth...its sorta like touching soap stone, but different...definately have a finish on them that you couldn't get on a ferrous alloy. 

                                                          

Date: Wed, 17 Mar 1999 11:46:59 -0800
From: "Jim LaBreck (Solutions IQ)" 

I made the mistake of spending nearly $1,900 on 3mm Ianetti 2-piece ceramic seals. While I concede that they will stand more abuse than the factory
seals, detonation will still break both. Sandy reported that the ceramic seals in his engine withstood several good detonation pops before breaking while
Mandeville was trying to tune his Motec, but that the replacement engines with factory 2mm seals only withstood one or two good pops. Proof that
both will break, but that the ceramics will withstand more abuse. The point? Don't detonate. 

3mm factory seals chatter, increase the problems of poor lubrication at the seal edges (away from the MOP injection port) and will eventually chip and
wear both seals and housing. Brooks has first hand knowledge of this problem, which can only be combated by running pre-mix oil in the gas tank, as
far as I know. Short of increasing the number of MOP ports in the housing, there is no way to ensure that enough lubricating oil reaches the edges of
the seals to reduce wear besides running pre-mix. Someone correct me if I'm wrong, thanks. 

The additional mass of the 3mm seals also makes them float at a lower rpm according to what I've heard from several sources. Floating is when the
apex seals are no longer in contact or in limited contact with the rotor housing's surface. At this point, they are no longer able to transfer heat to the
housing, and as a result, they may warp, bind, or break. Also, they are no longer doing an effective job of sealing the combustion process, and
pre-ignition and/or detonation are the resulting side effects. While the ceramic seals with their much lighter mass will resist floating to a greater
extent, the real solution is not to turn a turbocharged motor to rpms that a N/A motor would be comfortable with. The factory 2mm seals float at
approximately 8,000 rpm, and I've been told that the factory 3mm seals will float under boost at a somewhat lower rpm, making them somewhat less
effective in the operational range of the 13B-REW. The factory 2mm seals are sufficient providing that enough fuel is being administered, and with
the possible addition of a solid corner seal. 

While there are some people who are enthralled by technology to the exclusion of objective reason (and I don't omit myself from this category in
certain situations), those people (and I'm not naming any names, but one of them was the key reason why I wasted $1,890 on the ceramic seals which
are now in an engine which his father owns, with my loss on the engine almost equivalent to the cost of the seals...) should examine the problem from a
different viewpoint. It is not building a bigger or better seal that is the solution. The solution is providing an adequate amount of fuel to eliminate or
drastically reduce the possibility of detonation. 

If when I started modifying my car someone had had the knowledge and foresight to advise that I spend as much or more on my fuel system as on other
mods, I probably would have had a much better engine history. Of course there's no guarantee that something else won't happen, and with my first
engine, that happened to be the stock clutch letting go at increased power levels. The result was a thrown corner seal on the rear rotor at about 14,000
rpm. No one had the knowledge or foresight to advise me to upgrade my clutch at the same time I was doing all of my initial mods, either, but that's the
way it goes. Stressing the importance of proper fuel delivery is very important, in my opinion. 

My advice? Save the money you would normally spend on those Blitz rims, the VeilSide body kit, a huge intercooler, 3mm ceramic seals, or whatever
else you really could live without, and sink it into a comprehensive fuel system upgrade. 

One solution is to scrap the factory ECU, since it really can't cope with delivering fuel in a satisfactory method for 2-rotor engines producing more
than 400 horsepower anyway, and spend the money on a stand-alone aftermarket fuel computer from Haltech, Electromotive, or if you have the funds,
a Motec. 

Another solution is to use a piggyback fuel computer to adjust delivery to larger injectors, like Carlos and others have managed with greater or lesser
success with the PFS purple box. Then get some bigger injectors. Get a bigger fuel pump. Get larger fuel line. Once you have these mods, you can (as
Tri-Point has proven) run any combination of intake, downpipe, midpipe, and exhaust you want with almost no need to control boost (the Tri-Point
downpipe actually causes spiking by design, I've heard) and be assured that you have enough fuel for any situation to prevent the detonation that no
magic apex seal will live through. 

Just my opinion after two motors, untold thousands of dollars invested, and a full working knowledge of how almost each and every part on my car is
removed, is reinstalled, and how it operates... your mileage may vary. 

_______________ 

Jim responds on why he didn't use his 3mm ceramic seals... 

Date: Sun, 5 Dec 1999 15:28:39 -0800
From: "Jim LaBreck" (jimlab@earthlink.net) 

Never fired up the engine they were put into, that's why. That was the now infamous Hayes Rotary engine where I got taken for a bundle AND a mint
6,000 mile '95 core (with one bad rotor and one bad housing), which they kept and substituted heavily used (and wrong year) parts for. 

That engine was dropped into the car, and of course I realized that I'd probably just blow it up, and since it was too pretty to do that to, I decided to let
someone else have that honor. And they have. :) Actually, I think it's only been overheated, probably due to more shoddy Hayes Rotary assembly, with
less than 2,000 miles of use, but the apex seals should be fine. Not my problem any more. :) 

Without starting another huge debate over which is better, simply realize that moving up to 3mm OEM seals increases the weight and width of the
seals by 50%. The metering oil system cannot provide an adequate amount of lubrication, especially since it injects at the center of the housing, so the
outside edges of the seal are going to be subjected to 50% more wear and tear than if they were 2mm seals. As people have found out, this can lead to
chipping of the surface of the rotor housing and cracking and chipping of the outer edges of the apex seals, resulting in reduced efficiency in sealing the
combustion process and hence less power. 

50% more mass in the seal also means that the point at which they float (pull away from the housing) will occur at a lower rpm (or so I've been told).
At that point, they are no longer transferring heat or sealing effectively, so they will tend to warp or crack, and pre-ignition can occur because of poor
sealing. This is at high rpm, obviously, near redline.This does not occur, I'm also told, in engines which are not under pressure, so 3mm steel seals in a
naturally aspirated engine work just fine. I got this information indirectly from Francesco Ianetti, the maker of the ceramic seals, so it may be a load of
"sales pitch", but I've never had anyone argue that this wasn't the case. 

The cure to the lubrication problem is to run pre-mix (oil) in the fuel. It's a pain, of course, but can prevent several problems. The facts are, though,
that there are many high performance engines using the stock 2mm seals. The benefits of this, beside the fact that they're cheap, are that the rotors
can then be machined for 3mm seals if anything bad happens, more often than not. Where do you go when you're already at 3mm? 4mm? Maybe, but
more likely, it's time for a new rotor. Also, they wear less, seal fairly effectively, and are cheap to replace if no damage is done to the rotor or housing in
the process. Where the 3mm seals do have an advantage over the 2mm seals is that a solid corner seal can be used, which keeps the seal aligned in the
rotor groove and prevents the corner seal from breaking. Or at least from breaking as readily. When the corner seal lets go, scoring of the side plates is
almost inevitable. It also allows the apex seal to move much too readily in its groove, which often cause the apex seal to fail as well. This usually results
in at least one side plate being replaced as well as the rotor housing and rotor, and more than likely the turbine blades of the rear turbo. 

A ceramic seal's main benefits are reduced weight and reduced wear. They are almost impervious to wear, and with a significant reduction in weight,
they are far less likely to float under pressure. They are, however, extremely expensive, and they will break just like a standard apex seal. They will
withstand a bit more abuse, and will withstand more detonation than a factory apex seal, but they will break eventually, just the same. Sandy Linthicum
said that when he was having Mandeville Racing tune his engine and Motec system, that because of a bad harness, the engine(s) were detonating badly.
He mentioned that the ceramic seals he was using held up to several loud pops before breaking. Past that point, they used engines with 2mm standard
seals, I believe, and he said that they broke after only one or two pops (detonation). The bad harness was eventually diagnosed as the cause of their
problems, and I believe he then had the final engine built with ceramic seals. Since he's one of only a few that I know of using them, or having used
them, you might contact him for more information on his experiences. 

Personally, I don't see that they're worth the extra money. You could replace your rear rotor, housing, and seals at least twice for the price of the
ceramic seals. With proper and careful tuning, you shouldn't have to replace anything. I never expected to get 100,000 miles out of any of my engines.
In fact, I've never put more than 30-35,000 miles on any car I've ever owned, so longevity wasn't a concern. I was looking for a snake oil cure-all
which would keep me from blowing any more engines, and these aren't it. I'd recommend investing the extra money in your fuel system and engine
management system, to be perfectly honest. Spend the money there and you won't be needing to replace seals, ceramic or otherwise. 

As for damage to the engine when they disintegrate, I can't verify one way or another. I've never blown up a ceramic seal engine and been able to
inspect the damage. I would suspect that you may save your rear turbo because the Inconel blades will probably survive slicing and dicing the ceramic
material whereas they will not survive intact if a standard apex seal goes through them. I speak from experience here. :) I also don't know if they'd be
crushed to powder internally and save the rotor housing from being destroyed, but I tend to doubt it. They may minimize damage, but I don't think
they'll simply come apart and leave everything else intact. 

                                                          

Date: Wed, 17 Mar 1999 20:19:06 -0500
From: Sandy Linthicum 

I have a set of the one piece 3mm Ianatti seals in it. They are good to about 45psi of boost (assuming the engine is properly tuned for it). We broke a set
of the 2 piece 2mm Ianatti seals on the dyno after 15-20 severe instances of detonation (ie. sounding like someone threw about a trashcan full of cans
down concrete stairs). Even then, only one seal broke on the tip. 

The 2 piece Ianatti seals, provide superior sealing at lower rpm and give better compression, hp & torque at these rpms. At higher rpm ther is minimal
difference. Being a single piece, the one piece design is clearly superior in strength and gives you much more margin when things go out of spec. The
Ianatti design concept is not directed towards making the seals impervious to detonation but towards improved performance. 

Iannati/ceramic seals are approx 50% lighter than steel, do not expand or contract on temp change (practically), do not absorb water and have less than
1/2 the friction of steel seals. In my application this allows using competition apex seal springs to give greater spring pressure while still keeping
friction below that of a 2mm stock seal. This low friction and the characteristics of the ceramic also make rotor housing wear virtually zero. Of course
the seal do not wear at all either and can be used rebuild after rebuild. 

Now, whether they are worth the additional $900 (ie. $1200 for a set compared to $300 for stock seals) is another matter - they were worth it for me. 

The use of them however is not a simple swap for the steel seals, characteristics are different and matching dimensions, clearances and parts is much
more critial. 

                                                          

Date: Tue, 30 Mar 1999 15:58:22 -0500
From: Tom Walsh (TWalsh@achieversusa.com) 

Time for an update to the on going "Life and Trials of Tom Walsh" story. As some may know, my previous motor let go on February 1st. It has taken
me 2 months and more money that I care to calculate, but I am now the proud owner of a brand new 13B-REW rebuild courtesy of Pettit Racing. 

(snip) 

3mm Apex Seals, but not your everyday "run of the mill" 3mm apex seals. These are the Hurley Engineering 2 piece seals with the enlarged corner seal
section, and straight 45 degree cut between the pieces. Of course I am the first motor that Cam has put these in, so who knows how good they really
are... I am the "guinea pig". 

http://www.hurley-engineering.ltd.uk/HME_Longlife_Tip_Seals.htm 

This is a direct link to the frames page to get a better idea of what I am talking about. (I tried to get the link all on one line, so it will be easier to click
on.) 

________________ 

Date: Thu, 13 May 1999 06:42:19 -0400
From: John.Duarte@clariant.com 

I have been running 3mm seals made by "RX7 Speacialits" of Canada which are similar in design as the "Hurley" seals with the bigger corner piece.
They took longer to break in but have been holding up to quite bit of detonation. Seals are made of the same material used for racing piston rings and
that's all I know... 

_________________ 

From: Fastrotor@aol.com
Date: September 5, 2000 

My name is juan barajas. I have been running 2 different engines one running high boost and the other bridgeport holley. I have tried seals from hurley
in europe and the atkins seals and had nothing but problems. 

The problem with the Atkins seals is the radius on top of the apex seal is completely flat causing low compression. 

The Hurley seals did not last long they detonated after a few dyno runs and ended up broken.The problem with the Hurley seal I was told is the corner
chip is too large causing blow by ending up in pre-detonation. 

This is why mazda made there corner chips small to avoid blow by. After all my engine blowing adventures I was referred to a racing shop in California
that makes custom parts for Mazda rotary engines. He suggested to me to purchase his 2mm metal apex seals and 2mm solid corner seals. He said this
is the right remody for my problem. Ever since I have had no problems with engines and have one person to thank: POWERHOUSE ENGINEERING.
Their web site is www.mazdacomp.com. Tell them juan barajas sent ya!! 

(Editor's note: this is NOT Mazda Comp, which is how everyone refers to Mazda Competition Parts, Mazda's parts group. Just wanted to clear up any
confusion. --Steve) 


 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org