I'm not looking at using it for the motor mount at all. That's
why I only want enough sticking out to mount the starter. I'm going
to do
the sandwich with the oil pan that includes the windage tray (keeps the
aerobatic oil displacement under control). This will extend out the side
and rest on a bed mount I'm working on.
I don't have any good drawings to send yet or I would. I
quickly
plagiarized one of your RV-4 mount drawings to give you an idea of
what I'm
talking about. The RV-4 has a sort of tunnel that runs forward from the
spar (F-413R & L for the RV-4 guys). I am going to extend that and
have it
widen out enough to let the engine rest on it. It will require some
rework
of the fire wall and a work around for the gear but I think when it ties
into the forward fuse it will be a little cleaner and stiffer than trying
to work with the original mount system. It sounds complicated but as
much
as I've thought about it, looked at the plans and sketched it out it
really
isn't. I'm going to try and get this CADed up this week and I'll post it
up for critique.
Ya know, the more I look at this the more I think I should just
cut up a bell housing for the redrive mount.
Mike
Mike McGee, RV-4 N996RV, O320-E2G, Aurora, OR
13B in gestation mode
Not a bad idea. The Bonanza, Cessna P210 and the Questair Venture use an
aluminum structural lower cowl. You will need to feed those landing
gear tube socket loads into something substantial. Where are the rubber
mounts?
The bell housing is too deep. It needs to be 3.040 inches
deep as I recall.
Paul Lamar
Hi Mike,
That is a really interesting idea. There are 4 of us on the list
building RV-4's and we are all developing a different mount system. Mike
Wills is in the lead though, as he is the only one close to flying. I am
taking Paul and Mike W.'s advise while trying to develope a cantilever
system in order to keep the motor mount out of the way of the radiators
and exhaust. Mike's last bit of advise to me was to spend the extra $200
for a custon CR Radiator and not be limited by the stock radiator sizes.
Ken Powell
kenpowell@aristotle.net
After staring at the plans for a while it just seemed like the way
to go. I think that going through the fire wall is something of a
psychological barrier. Once past that and really looking at things I
<<THINK>> it's going to work. I still am planning to run it by some of the
local experts including Van if I can get him to look it. I'm an engineer
but I live in the world of schematics.
Next time I'm down at the in-laws in Los Osos (San Louis Obispo) I
am hoping to have the time to run on down and look at Mike W's plane
closer. Since it's almost winter, he may be flying before I get
there. That's what I intend my plane to look like.
I expected to have to buy a custom rad although since I have to
build a new cowl anyway I should be able to accommodate one of the standard
sizes. We'll see.
Mike
Mike McGee, RV-4 N996RV, O320-E2G, Aurora, OR
13B in gestation mode
Here is a bad reproduction of that part of the plans.
I'll take it to Kinkos and see if they can convert it to a
better gif. My scanner is down again.
I happened to have a set of RV4 plans lying around.
It looks very feasible to me Mike. One thing though you need
to figure a way of stabilizing the top of the extended box
for torsional stiffness reasons and still get an oil pan in there.
Perhaps two small 1/2 tubes from the front ends of the sheet metal
box back to the lower motor mount hard points will work.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org