Paul Lamar Wrote:
If you increase the temp of the coolant going into the radiator the temp
of the water coming out will also be increased all other things being
equal. That means the temp of the coolant going into the engine block
will also be higher which is not a good thing.
Jon Wrote:
I agree with Tracy. (I also agree with Paul, but on a slightly different
aspect!) The original post was an oversimplification. This kind of thing
leads to people making snap judgements instead of working through the
calculations to see the trends and effects. If you raise the coolant
temperature into the radiator 1 degree you will raise the coolant
temperature out of the radiator by LESS THAN one degree.
snips.... After that the vast majority of which I agree with.
I want to deal with just this part. I agree; if you raise the temp going
into the
rad by 1 degree the temp coming out of the rad will be raised by less than
one degree due to what Tracy said about the rate of heat transfer increasing.
Now here is the rub. Liquid coolant systems have very small margins of safety
before they become divergently unstable and melt down occurs.
Let me quote my article on cooling systems located on the ACRE NL
web site because I have said it all before.
"In an air cooled engine waste heat is transferred by the fins on
head and cylinders directly to the air. This is done first by
conduction and then by convection. The rate of heat transfer is
proportional to the difference in temperature between the fins and
the surrounding air. This difference, initially, is about 400
degrees. The metal surface surrounding the combustion chamber is
500 degrees and the ambient air temperature surrounding the fins
is about 100 degrees F. If the engine gets hotter the rate of heat
transfer increases. In a sense this is a stable cooling system. The
fin density or number of fins per inch of head or cylinder surface
must be such that the rate of heat transfer to the air keeps the
hottest part of the combustion chamber below the melting temperature
of the metal. Usually aluminum."
Now for a water cooled engine:
"If the temperature of the bulk coolant goes beyond the boiling
temperature overall boiling occurs of course. All hell breaks
loose and the coolant is forced out of the water jacket through the
pressure cap overflow valve by massive amounts of hot vapor or
steam. Once boiling of the coolant starts it is all over. Less
coolant, hotter metal, more steam. Things go to hell in a hand
basket very very quickly indeed. The cooling system pops like a pop
corn. Thus the cooling system becomes very unstable indeed. Something
we all have probably experienced in our cars. This is a major
difference between the air cooled engine and the liquid cooled
engine. Needless to say this cannot be allowed to happen in an
aircraft engine.
A few bad experiences like this during climb out can be very
discouraging indeed. Forget all you have learned about car
overheating. You cannot just quickly reduce power and pull over to
the side of the road and stop. It is best to test your new water
cooled airplane at low use uncontrolled airports so you can get it
back on the ground right now! Otherwise you may damage your engine."
End of quote.
Every degree you add to the water cooling system reduces this margin
of safety. It is extremely important that everyone building a liquid cooled
aircraft engine thoroughly understand this problem.
An air oil heat exchanger on the other hand does not have this problem.
It is stable as the boiling temp of oil is probably around 300 to
400 degrees and there is no pressure pop off valve with an overboard
dump hose. In light of this I would be much quicker to embrace a totally
oil cooled engine than a water oil heat exchanger.
Paul Lamar
This is why I wish we had an aircooled engine to work with. We don't,
that is unlikely to change in any reasonable time frame, so too bad. And
aircooling has it's own problems, like poor cabin heaters. But
we DO need to understand the limitations of liquid cooling. One other
item that may not be clear from Paul's excellent treatise on the subject -
that even with a large excess capacity in the radiator, if the heat transfer
inside
the engine is inadequate locally you can still damage the engine. This bears
repeating: If you have a radiator that will cool properly at 80 HP, and
increase the output to 160 HP, a double or even triple capacity radiator
MAY not provide adequate cooling. Increased coolant flow rates and
possibly even internal finning could possibly be required to pull enough
heat from the metal to the coolant. There are two "choke points" in
the heat flow from the metal to the air; metal-to-coolant and coolant-to-
air. The radiator size, construction, airflow, plumbing, etc ONLY affect
the latter. The former is controlled by coolant type, flow rate, metal-to-
coolant contact area and metal surface shape/roughness.
The good news is that up to about 150 HP or a bit more (continuous)
it appears that there is no problem with the 13b, as far as internal
passages and local coolant flow rates. It may be a problem at some
higher HP level, so we need to be aware if this.
Bill Freeman
Long EZ builder & pilot
BSME, MSME
EAA Technical Counselor
Lynn Hanover is working on this. He recognize the problem and has
offered to install a thermal couple down near the combustion chamber
when he gets an opportunity. A CHT gage if you will. Some of the early work
along these lines was focused on the carbon build up on the rotor
housing just after the hump. The thinking then was the excessive high temp
of the housing was causing the crankcase oil to coke. Attempts were made to groove
the water jacket to improve the heat transfer from
metal to coolant. This apparently worked but I suspect that was a bit
mis directed as two cycle apex lube oil burns cleanly and does not coke.
The temperature limit as I perceive it now is the structural
effect on the aluminum rotor housing. Same as an air cooled cylinder
head.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org