Subject: Dry sump? RX8 press release intake air velocity.
From: ACRE NL
Date: 1/9/2002, 12:54 PM


As always, I offer a $500.00 reward to anyone who can show proof
that intake
air velocity is not important to intake system tuning.

Tracy Crook
tcrook@rotaryaviation.com
www.rotaryaviation.com


Here is a very good illustration from Taylor. This is volumetric
efficiency as
a function of Mach number (Z) for a number of actual engines with a
number of differnt
intake manifolds and carbs. As you can see at lower RPMs the vol eff
is increasing
hence the power is increasing as the flow increases and as the intake
pipe length
is becoming closer to its tuned length what ever that is. As the Mach
number goes
above about 0.45 Mach things start going down hill. 0.45 is a magic
Mach number in
intakes and this number shows up in a lot of Taylor's work. If you
want lots
of power keep the Mach number less than 0.45 and that means larger
pipes
for more power at higher RPMs.

OK Tracy put the check in the mail NOW!!!

Paul Lamar

Paul, didn't you just make Tracey's point that velocity does matter?

Hans


Its a question of semantics. That is not what he meant, What he meant was
air
velocity can be too low for a given RPM. I maintain that for any RPM
the vol eff will get better as the pipe gets bigger and the air velocity
goes down. There is no question that up to a point (0.45 Mach) higher
velocity means more air in the engine as the RPM increases. That is
consistent of course with how a pump works. More RPM more air. An ICE
is just a glorified air pump of course. I think the myth got started
in the old days when you needed a lot of velocity to mix fuel with
the air in a venturi. That does not apply with fuel injection.

Several of us were sitting on Tracy's porch during the rotary round up
and Ed Anderson brought this up. I shouted: "Ed! Don't spread myths
like that!" Most people got up and walked away. Poor Ed had to sit
there awhile and listen to me rant and rave about it. :-)>
Robin took a picture.

Paul Lamar


I agree, I DID mean that air velocity can be too low (for any given rpm).
And I agree that I thought you were saying
You said, " I maintain that for any RPM,  the vol eff will get better as the
pipe gets bigger and the air velocity goes down."  Note that you did not put
a lower limit on this assertion, i.e., lower is better.  What I am saying
(still) is that the velocity is a necessary component to high VEs.

There is no lower limit. Think how well a piston engine would breath
if there were no cylinder head or valves to get in the way. 

At bottom dead center, due to the inertia of the column of air above the piston,
the mass of air would be greater than the mass of air down there 
when the piston was stationary for awhile at bottom dead center. 
The VE would be greater than 100%.
Basically a peripheral port rotary comes close to that ideal.

  Can't write the check yet because the data provided so far clearly shows
that velocity IS important and if it is too low, volumetric efficiency will
suffer.

I don't think it is a matter of semantics, I think it is a question of
relativity.  How high is high?  The chart you provided shows  VE
improvements up to almost Mach .5  Note that this is on fairly dated engines
and that the later engines with the highest VEs benefited from the highest
velocities.  The rotary is up in the 1.25 VE range so I'm sure the optimum
velocity would be well above any of those in the Taylor chart.   Again, my
real point is that it is the energy in the moving column of air (velocity)
that makes high volumetric effeciencies (in normally aspirated engines)
possible.

Tracy Crook
tcrook@rotaryaviation.com
www.rotaryaviation.com

I thought you would try to wiggle out of it.
That's OK. I will come down there and live with you for a week and you will
have to feed me :-)>

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org