Subject: stratified charge - was exhaust heat
From: ACRE NL
Date: 1/18/2002, 8:45 AM
CC: Jim Mederer


<< > > > > > We'd love to build stratified charge engines. Anyone got $5MM
laying around to help?
 > > > > >
 > > > > > Jon
 > >
 > > > > Is that all?


 > > > I believe that a medium displacement stratified charge engine can be
designed, tooled, and taken to the prototype demonstrator stage for about $5
million. The larger the engine gets, the more difficult the development.
(Very small is probably hard to do also, but I don't think anyone wants
something lawnmower sized.) Curtiss-Wright/Deere/RPI worked under government
contract, which adds quite a bit of cost for things that are not directly
related to the product (not necessarily bad things, but perhaps less
necessary for a "lean" commercial effort). The overhead structures at the
companies were also very, very high. I think the marine and aviation engines
would have similar base ratings -- say 400 hp at 5000 RPM?  I think we
already have some of the capabilities within the folks on the list, plus a
few others. This could be done as a "virtual company," with a lot of CAD
drawings flying through the ether...
 > > > Anyone game?
 > > >
 > > > Jon Lauter
 > > > Rotary Power Marine Corporation


 > > Starting with a Mazda I hope. I have a few ideas.
 > > As the rotor comes up to top dead center the squish area on the trailing
side
 > > gets smaller and some mixture squishes out of there. If the rotor could
 > > be grooved in such a way to squish the mixture in a way that concentrate
it towards
 > > the spark plug the natural stratified charge of the rotary might
 > > be enhanced. Some sort of glass rotary engine could be made to
 > > high speed photograph the ebb and flow of the mixture during this phase.
 > > Not one that runs of course. Just for the purpose of studying the
 > > aerodynamics in the compression and  combustion chamber.
 > > Perhaps a bit of high pressure fresh air could be injected at
 > > just the right time in this small volume squish area to purge it of
 > > fuel rich mixture. Nothing burns in there anyway.
 > >
 > > Paul Lamar

 > I believe that a stratified charge engine will have little or no gain for
aircraft.
 > The big gain is
 > at low throttle settings where it minimizes throttling losses and allows
full expansion
 > with reduced heat input - much as the so called Diesel engine. Most
aircraft
 > use is at larger throttle openings where direct injection engines will
often have
 > poorer power and specific consumption because mixing with a full charge is
 > better with the vaporization and gaseous mixing of a carb or port
injection.
 > (for example Diesel smoke at full power)
 > Vance


 Thats true for most combustion chambers Vance but I think there is more
 to be had out of the wankel chamber with some sort of strat charge.
 At least CW and JD got below .4 in a wank with strat charge.

 I have been thinking about my air injection scheme and I have convinced
 myself that it is a good idea :-)> You don't need a lot of volume
 and pressure. Just before the mixture fires it is probably only about
 150 PSI max in the combustion chamber. If you squirt the fresh air
 in on the trailing side it should purge that area of mixture
 and get the explosive stuff up towards the leading edge of the
 combustion chamber where it wants to burn anyway.

 You are talking conventional direct injection strat charge and I am talking
 mixing the fuel well with the air in the intake runners and then converting
 the homogenous charge in the combustion chamber to strat charge. Making the
 trailing side super lean with the additional fresh air. It would also
 be a slight supercharge effect.

 The big question is; will the additional HP required by the air compressor
 negate any improvement in the BSFC? The best compressor would be driven
 by a geared exhaust gas  blow down turbine.

 What do you think Jon?

 I also think one of use could try this.

 Paul Lamar 


Haven't had time yet to evaluate your concept, Paul, but knowing who the
inventor is, I'm sure it has potential :-)

Aside from the efficiency benefit of a direct injected stratifed charge
engine, a very big benefit for general aviation use is the ability to burn
JetA. That is also the key to the engine's desirability for military and
commercial marine applications.

Jon

Yes I agree that may be a real driving force if 100LL continues its
price climb. Perhaps the spark assisted direct injection of heavy
fuel as demonstrated by Wankel Gmbh would be an interim first step.

BTW getting a couple of four rotor rotor housings and replacing
the third or top spark plug with a shop air fitting would be a cheap way
of testing my invention. Maybe even just removing the 13B trailing
plug and hooking up shop air just to see what happens. A ball
check valve might be advisable when the combustion pressure
exceeds the shop air pressure.

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org

Four-rotor-leman.jpg